Mercury HP700 SCi Скачать руководство пользователя страница 133

Страница: 133 / 138

TROUBLESHOOTING

125

Remote Control Operates Hard, Binds, Has

Excessive Free‑Play or Makes Unusual Sounds

Possible Cause

Remedy

Insufficient lubrication on shift and throttle

linkage fasteners.

Lubricate.

Loose or missing shift and throttle linkage

fasteners.

Check all linkages. If any are loose

or missing, see authorized Mercury

Marine dealer immediately.

Shift or throttle cable kinked.

Replace cable.

Friction adjustment excessive.

Adjust friction.

Steering Wheel Turns Hard or Jerky

Possible Cause

Remedy

Low power steering pump fluid level. Refill system with fluid and check for

leaks.

Sepentine belt loose or damaged.

Replace and/or adjust.

Insufficient lubrication on steering

system components.

Lubricate.

Loose or missing steering fasteners or

parts.

Check all parts and fasteners. If any are

loose or missing, see authorized

Mercury Marine dealer immediately.

Contaminated power steering fluid.

Drain and replace.

Air in system

Purge air from system

Seawater Pressure Is Below Specification

Possible Cause

Remedy

Insufficient water supply.

Check if seacock is completely open.
Check supply hoses for obstruction.
Check for external water pick‑up obstruction.
Check for sea strainer obstruction.
Check condition of sea pump.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 133 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: