Mercury HP700 SCi Скачать руководство пользователя страница 103

Страница: 103 / 138

MAINTENANCE

1. Inspect seawater pump impeller if insufficient seawater flow

occurs or if operating temperature exceeds normal range.

8022

a -

Seawater pump

Cleaning the Seawater (Raw Water) Section of the

Engine Oil, Power Steering, Fuel, and Transmission

Coolers

NOTICE

An open seawater strainer or seacock during some service or

maintenance procedures can introduce water into the boat,

causing damage or sinking the boat. Always close the water

supply from the seawater pump, water inlet, or seacock when

performing service or maintenance on the cooling system.

The seawater section of the oil cooler should be cleaned at least

once a year, or whenever decreased cooling efficiency is noticed.

ENGINE OIL COOLER
NOTE: The engine oil cooler is located on the top rear portion of

the engine.

1. Remove the end plates and gaskets.

8030

a -

End plates (2)

2. Clean the oil cooler with a suitable brush.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 103 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: