Mercury HP700 SCi Скачать руководство пользователя страница 130

Страница: 130 / 138

TROUBLESHOOTING

122

Engine Hard to Start, Runs Rough, Misses, and/or

Backfires

Possible Cause

Remedy

Faulty ignition system component.

Service ignition system.

Dirty fuel filter.

Replace filters.

Stale or contaminated fuel.

Drain the fuel tank and fill it with fresh

fuel.

Fuel line or fuel tank obstructed.

Replace damaged lines or clean out lines

with compressed air to remove the

obstruction.

Flame arrestor dirty.

Clean or replace the flame arrestor.

Rev limiter engaging at

wide‑open‑throttle.

Use a propeller with more pitch.

Poor Performance

Possible Cause

Remedy

Throttle not fully open.

Inspect throttle cable and linkages for proper

operation.

Damaged or incorrect propeller. Replace propeller.
Excessive bilge water.

Drain and check for cause of entry.

Boat overloaded or load

improperly distributed.

Reduce load or redistribute load more

evenly.

Boat bottom fouled or damaged. Clean or repair as necessary.
Flame arrestor dirty or restricted. Change or clean flame arrestor.

Stale or contaminated fuel.

If contaminated, drain tank. Fill with fresh

fuel.

Engine Coolant Temperature Too Low

Possible Cause

Remedy

Faulty coolant thermostat.

Replace water thermostat.

Faulty gauge or sender.

Test with shop gauge; test sender.

Faulty oil thermostat.

Replace.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 130 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: