Mercury HP700 SCi Скачать руководство пользователя страница 39

Страница: 39 / 138

SPECIFICATIONS

• The Environmental Protection Agency (EPA) requires that any

sterndrive manufactured after January 1, 2009 must use low

permeation fuel hose for the primary fuel hose connecting the

fuel tank to the engine.

• Low permeation hose is USCG Type B1‑15 or Type A1‑15,

defined as not exceeding 15/gm²/24 h with CE 10 fuel at

23 °C as specified in SAE J 1527 ‑ marine fuel hose.

Oil Recommendations

ENGINE CRANKCASE OIL

Preferred Oils

API Classification

Kendall GT‑1 Motor Oil 20W‑50

SJ, CF‑2, CH‑4

Oil Filter Should Always Be Changed With Oil

SUPERCHARGER GEARCASE OIL

Preferred Oils

API Classification

Castrol Syntec Synthetic Motor Oil 5W‑50

SL, SJ, CF

IMPORTANT OIL PRACTICES

Do Not Use

•

Straight weight oils

•

Non‑detergent oils

•

Oils containing solid additives

•

Multi‑viscosity oils other than the ones recommended

•

Low quality oils

Do Not Mix

•

Different brands of oils, straight weight or multi‑viscosity

•

Different weights of straight weight or different weights of multi‑viscosity

oils.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 39 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: