Mercury HP700 SCi Скачать руководство пользователя страница 2

Страница: 2 / 138

The product you have purchased comes with a limited warranty

from Mercury Marine; the terms of the warranty are set forth in the

Warranty Information

section of this manual. The warranty

statement contains a description of what is covered, what is not

covered, the duration of coverage, how to best obtain warranty

coverage, important disclaimers and limitations of damages, and

other related information. Please review this important

information.

Safety Alerts and Notices

Throughout this publication, dangers, warnings, cautions, and
notices

, accompanied by the international HAZARD symbol

, are used to alert the boat operator and technician to special

instructions concerning a particular service or operation that may

be hazardous if performed incorrectly or carelessly. Observe these

safety alerts carefully.
These safety alerts alone can not eliminate the hazards they

signal. Strict compliance to these special instructions when

performing the service, and common sense operation are major

accident prevention measures.

DANGER

Indicates a hazardous situation which, if not avoided, will result

in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result

in minor or moderate injury.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 2 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: