Mercury HP700 SCi Скачать руководство пользователя страница 121

Страница: 121 / 138

COLD WEATHER OR EXTENDED STORAGE

113

IMPORTANT: Do not run the engine's fuel system dry of the

fogging mixture in the 23 liter (6 U.S. gal) remote outboard fuel

tank.

11.Check the water discharge from the engine. It should be clear

when the system is properly flushed. Refer to

Maintenance

- Flushing Cooling System

12.After the specified running time is complete, slowly return the

throttle to idle RPM and shut off the engine.

13.Shut off the water tap.
14.Drain the seawater cooling system and if desired, flush the

system with anitfreeze as explained in

Cold Weather or

Extended Storage - Cooling System Draining
Instructions

. When running the engine, use the fogging

mixture as the fuel supply.

15.Perform all engine and transmission maintenance

procedures. Refer to

Maintenance - Changing Fluids

of this

manual.

16.Perform the draining procedures. Refer to

Cold Weather or

Extended Storage - Cooling System Draining
Instructions

17.Perform battery maintenance. Refer to

Cold Weather or

Extended Storage - Battery Storage

18.Perform all drive unit and trim pump maintenance

procedures. Refer to

Maintenance - Changing Fluids

and

Maintenance - Changing Drive Unit Gear Lube

19.The drive unit should be stored in the full down position.

NOTICE

The universal joint bellows may develop a set when stored in a

raised or up position, causing the bellows to fail when returned

to service and allowing water to enter the boat. Store the

sterndrive in the full down position.

20.Perform all yearly checks, inspections, lubrication and fluid

changes as outlined in the

Maintenance Chart

of this

manual.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 121 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: