Mercury HP700 SCi Скачать руководство пользователя страница 70

Страница: 70 / 138

MAINTENANCE

1. Stop the engine.
2. Allow approximately five minutes for the oil to drain into the oil

pan. The boat must be at rest in the water or at the

approximate angle that it would be if setting in the water.

3. Remove the dipstick, wipe it clean, and re‑install it all the way

into the dipstick tube.

4. Remove the dipstick and check the oil level. The oil level must

be between the "OK RANGE" and the "ADD" marks.

5. If the oil level is at or below the "ADD" mark, remove the oil

filler cap (port or starboard). Add enough oil to bring the level

into the "OK RANGE" on the dipstick. Do not overfill.

IMPORTANT: Do not overfill the crankcase with oil.

ADD

OK RANGE

9987

a -

Oil level dipstick

b -

Crankcase oil filler cap

Tube Ref No.

Description

Where Used

Part No.

Kendall GT-1 SAE

20W50

Engine crankcase

Obtain Locally

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 70 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: