Mercury HP700 SCi Скачать руководство пользователя страница 109

Страница: 109 / 138

MAINTENANCE

101

INSPECTING BELTS
NOTE: Minor, transverse cracks (across the belt width) may be

acceptable. Longitudinal cracks (in the direction of belt length) that

join transverse cracks are not acceptable.

6164

a -

Fraying

b -

Transverse cracks

c -

Longitudinal cracks

The belt will have to be replaced for the following conditions:

• Excessive wear
• Cracks as explained previously
• Fraying
• Glazed surfaces

Fuel Filters

WATER SEPARATING FUEL FILTER

WARNING

Fuel is flammable and explosive. Ensure the key switch is off and

the lanyard is positioned so that the engine cannot start. Do not

smoke or allow sources of spark or open flame in the area while

servicing. Keep the work area well ventilated and avoid

prolonged exposure to vapors. Always check for leaks before

attempting to start the engine and wipe up any spilled fuel

immediately.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 109 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: