Mercury HP700 SCi Скачать руководство пользователя страница 3

Страница: 3 / 138

iii

NOTICE

Indicates a situation which, if not avoided, could result in engine

or major component failure.

IMPORTANT: Identifies information essential to the successful

completion of the task.

NOTE: Indicates information that helps in the understanding of a

particular step or action.

WARNING

The engine exhaust from this product contains chemicals known

to the state of California to cause cancer, birth defects or other

reproductive harm.

Mercury Marine, Fond du Lac, Wisconsin U.S.A.
Printed in U.S.A.
© 2009, Mercury Marine
Mercury, Mercury Marine, MerCruiser, Mercury MerCruiser,

Mercury Racing, Mercury Precision Parts, Mercury Propellers,

Mariner, Verado, Vazer, #1 On The Water, Alpha, Bravo, Pro

Max, OptiMax, Sport‑Jet, K‑Planes, MerCathode, SmartCraft,

VesselView, Quicksilver, Zero Effort, M with Waves logo, Mercury

with Waves logo, and SmartCraft logo are all registered

trademarks of Brunswick Corporation. Mercury Product Protection

logo is a registered service mark of Brunswick Corporation.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 3 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: