Mercury HP700 SCi Скачать руководство пользователя страница 102

Страница: 102 / 138

MAINTENANCE

Flushing Cooling System

WARNING

Rotating propellers can cause serious injury or death. Never

operate the boat out of the water with a propeller installed. Before

installing or removing a propeller, place the drive unit in neutral

and engage the lanyard stop switch to prevent the engine from

starting. Place a block of wood between the propeller blade and

the anti‑ventilation plate.

NOTICE

Operating the engine out of the water at high speeds creates

suction, which can collapse the water supply hose and overheat

the engine. Do not operate the engine above 1400 RPM out of

the water and without sufficient cooling water supply.

To prevent silt and salt build‑up in the cooling system, flush with

freshwater.

1. Install a flushing hose from a water tap to the flushing

connector/water pick‑up. Consult your boat owner's manual

for the location and procedures for water connection.

2. Completely open the water tap. Place the remote control in

neutral position and start the engine. Operate the engine at

idle speed, in neutral, for about 10 minutes or until discharge

water is clear. Stop the engine, shut off the water, and remove

the flushing hose.

Seawater Pump Impeller Inspection

Service should be performed by an authorized Mercury MerCruiser

dealer.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 102 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: