Mercury HP700 SCi Скачать руководство пользователя страница 120

Страница: 120 / 138

COLD WEATHER OR EXTENDED STORAGE

112

7. Connect the remote outboard fuel tank supply line to the

mechanical fuel pump inlet.

13030

a -

Mechanical fuel pump

b -

Fuel inlet

c -

Primer bulb (optional)

d -

23 L (6 U.S. gal) remote

outboard fuel tank

8. Open the water tap to supply enough water flow to the sea

pump so that suction created by the sea pump, does not

collapse the supply hose and cause the engine to overheat

while running.

WARNING

Fuel vapors trapped in the engine compartment may be an

irritant, cause difficulty breathing, or may ignite resulting in a

fire or explosion. Always ventilate the engine compartment

before servicing the power package.

9. Start the engine. If the engine has trouble starting and the

remote tank is equipped with a primer bulb, squeeze the

primer bulb until firm and attempt starting again.

10.Once the engine starts, run the engine at idle for a short

warm‑up period and then increase to 1300 RPM for a

minimum of five minutes.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 120 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: