Mercury HP700 SCi Скачать руководство пользователя страница 45

Страница: 45 / 138

OPERATION

Possible Cause

Horn

Monitor

Display

Guardian

Activated and

Engine Power

Reduced

Low Drive Lube

2 Beeps‑1 Sec. Long

Yes

Electrical System Overload Protection

If an electrical overload occurs, a fuse or circuit breaker opens.

Locate and correct the problem before replacing the fuse or

resetting the circuit breaker.
A circuit breaker protects the engine wiring harness and

instrumentation power lead. Reset by pushing the reset button.

7764

a -

Reset button

In an emergency, if you cannot locate and correct the cause of the

high current draw, and you must operate the engine, perform the

following:

1. Turn off or disconnect all accessories connected to the engine

and instrumentation wiring and reset the circuit breaker.

2. If the breaker remains open, electrical overload is still

present. Inspect the electrical system.

1. This message refers to Transmission Fluid Overheat. Check the transmission

fluid level if this message is displayed.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 45 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: