Mercury HP700 SCi Скачать руководство пользователя страница 40

Страница: 40 / 138

SPECIFICATIONS

TEMPERATURE/OIL VISCOSITY CHART

Multi-viscosity

Oil

-20

+20 +40

+60

+80 +100

SJ, CF-2,

CH-4

-20

-30

-10

+20

+30 +40

+10

Kendall 20W 50

9160

Capacities

Unit

Capacity

Fluid Type

Crankcase Oil

Capacity with New
Filter

7.6 L (8.5 U.S. qts)

Kendall Motor Oil 20W‑50

Supercharger

Gearcase

177 ml ( 6 U.S. oz)

Castrol Syntec Synthetic Motor Oil

5W‑50

Closed Cooling

System

Approximately 15

L (16 U.S. qts)

Dex‑Cool Extended Life Anitfreeze/

Coolant (50‑50 mix)

NXT¹ Drive Unit

Capacity

4.0 L (4.25 U.S.

qts)

High Performance Gear Lube

Six Drive Dry

Sump Unit Oil

Capacity

4.0 L (4.25 U.S.

qts)

Torco MTF Gear Lube

Transom Input

Shaft Bearing

Housing (Driveline

model)

0.47 L (0.5 U.S.

qts)

High Performance Gear Lube

Transmission fluid

capacity

Approximately 1.0

liter (1.1 U.S. qt.)

High Performance Gear Lube

1. Always use dipstick to determine exact quantity of oil required.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 40 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: