Mercury HP700 SCi Скачать руководство пользователя страница 88

Страница: 88 / 138

MAINTENANCE

Tube Ref

No.

Description

Where Used

Part No.

Kendall GT-1 SAE

20W50

Engine crankcase

Obtain Locally

15.Turn on the water supply hose to the water pick‑up.
16.Start the engine and check for proper oil pressure. Allow the

engine to idle for one minute and verify that no oil is leaking.

17.Shut off the engine and the water to the water pick‑up

attachment.

18.Wait a few minutes for the engine oil to return to the crankcase

and then check the oil level. If the oil level is low, add enough

oil to bring it within the "OK RANGE" on the dipstick. Do not

overfill.

19.Remove the external water supply.

CHANGING SUPERCHARGER GEARCASE OIL

IMPORTANT: Change the supercharger oil when the engine and

supercharger are warm from operation. Warm oil flows more

freely, carrying away more impurities. Use only the recommended

oil in the supercharger, see

Specifications.

If the oil level in the

sight‑glass has increased, decreased, or changed to an abnormal

color, there may be an internal problem with the supercharger.

Contact your authorized Mercury Marine dealer.

1. Attach a water hose to the boat's external water pickup, to

allow water to be supplied to the engine block during engine

warm‑up.

2. Open the water tap to supply enough flow to the sea pump so

that suction created by the sea pump, does not collapse the

supply hose.

3. Place the remote control in neutral position and start the

engine. Operate the engine at idle speed, in neutral, until the

engine reaches normal operating temperature.

4. Stop the engine and shut off the water.
5. Remove the fill plug from the top of the supercharger

gearcase.

6. Place a suitable container under the drain plug in the bottom

of the supercharger gearcase.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 88 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: