Mercury HP700 SCi Скачать руководство пользователя страница 110

Страница: 110 / 138

MAINTENANCE

102

1. Remove the water separating fuel filter (by turning

counter‑clockwise) and the sealing ring from the water

separating/fuel pressure regulator housing and discard.

9973

a -

Water separating/fuel pressure regulator housing

b -

Sealing ring

c -

Water separating fuel filter

2. Coat the sealing ring on the new filter with clean motor oil.

IMPORTANT: Do not use a filter wrench when installing the water

separating fuel filter.

3. Thread the filter clockwise onto the housing and tighten

securely by hand. Do not over‑tighten.

4. Start and run the engine. If the engine stops or will not start,

it may be necessary to prime the fuel system (see

Priming the

Fuel System Prior to Starting

in the

Cold Weather or

Extended Storage

section of this manual.)

5. Check the filter for gasoline leaks. If leaks exist, re‑check the

filter installation.

6. If leaks continue, stop the engine immediately and contact

your authorized Mercury Marine dealer.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 110 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: