Mercury HP700 SCi Скачать руководство пользователя страница 53

Страница: 53 / 138

OPERATION

1 -

Control -

Used to control both drive units from the

handle. Press up on the button(s) to trim drive unit up or

out. Press down on button(s) to trim drive unit down or in.

2 -

Trailer Button -

Press button until drive unit reaches

desired height to prevent the drive units from contacting the

ground while the boat is being trailered.

3 -

Three Button Trim Control (Trim Adjustment
Switches) -

With a single integral trim button in the handle

to control two drive units simultaneously, these two

switches control the fine tune adjustment of each drive

unit. Using these fine tune switches, set each drive unit to

the desired trim angle. Then use the single trim switch in

the handle to control the trim of both drive units

simultaneously.

Zero Effort Control with Integral Trim Switch

NOTICE

If using external tie bars, raising or lowering the drives

independently of each other can damage the drive and steering

systems. If using an external tie bar, raise and lower all drives

together as a unit.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 53 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: