Mercury HP700 SCi Скачать руководство пользователя страница 132

Страница: 132 / 138

TROUBLESHOOTING

124

Power Trim Does Not Operate (Motor Doesn't Run)

Possible Cause

Remedy

Open fuse.

Replace fuse.

Loose or dirty electrical

connections or damaged

wiring.

Check all associated electrical connections and

wires (especially battery cables). Clean and

tighten faulty connections. Repair or replace

damaged wiring.

Battery Will Not Come Up On Charge

Possible Cause

Remedy

Excessive current draw from

battery.

Turn off non‑essential accessories.

Loose or dirty electrical

connections or damaged wiring.

Check all associated electrical connections

and wires (especially battery cables). Clean

and tighten faulty connections. Repair or

replace damaged wiring.

Alternator drive belt loose or in

poor condition.

Replace and/or adjust.

Defective battery.

Test battery.

Power Trim Does Not Operate (Motor Runs But

Drive Unit Does Not Move)

Possible Cause

Remedy

Trim pump oil level low.

Fill pump with oil.

Drive binding in gimbal ring.

Check for obstruction.

Electrical Analog Trim Gauge Malfunction

Possible Cause

Remedy

Gauge indicates off‑scale high with no
self‑test

function.

Check wires between the sender and

the trim module.
Replace defective trim sender.

Gauge does not indicate properly but
the self test

function works.

Index the trim sender, test the trim

sender circuit or replace defective trim

sender.

1. Self‑test: When the key switch is placed to the "RUN" position, the pointer on

the analog gauge will sweep from the bottom of the scale to the top of the

scale and then point to the actual trim position.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 132 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: