Mercury HP700 SCi Скачать руководство пользователя страница 129

Страница: 129 / 138

TROUBLESHOOTING

121

Engine Will Not Crank

Possible Causes

Remedy

Battery switch "OFF".

Switch to "ON" position.

Remote control not in neutral position.

Position control lever to neutral.

Open 50 amp circuit breaker or 15 or 90

amp fuse circuit.

Check and reset circuit breaker or

replace fuse.

Master or starter solenoid defective.

Replace.

Loose or dirty electrical connections or

damaged wiring, battery cable diameter

(gauge) too small for the application.

Check all electrical connections and

wires (especially battery cables).

Clean and tighten faulty connection.

Low battery charge or defective battery.

Test and replace if defective.

Defective starter.

Test and replace if defective.

Defective key switch.

Replace.

Defective neutral/safety switch.

Replace.

Engine Cranks But Will Not Start

Possible Cause

Remedy

Improper starting procedure Read starting procedure
Low battery voltage

Charge the battery

Empty fuel tank or fuel shut off

valve closed

Fill tank or open valve

Faulty fuel pump, wiring, fuel

pump fuse, 50 amp circuit

breaker or a fuel pump relay

Replace faulty component

Faulty ignition system

component

Service ignition system

Lanyard Stop Activated

Reset

Obstructed fuel filter

Replace filters

Stale or contaminated fuel

If contaminated, drain tank and fill with fresh fuel

Fuel line or tank vent line

kinked or restricted

Replace kinked lines or blow out lines with

compressed air to remove obstruction

Crankshaft position sensor

faulty

Test and replace if faulty

Faulty fuel pressure regulator

diaphragm

Test and replace if faulty. Do not attempt to start

the engine if the fuel pressure regulator

diaphragm is ruptured.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 129 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: