Mercury HP700 SCi Скачать руководство пользователя страница 28

Страница: 28 / 138

GENERAL INFORMATION

Reduce speed and proceed with caution whenever you drive a

boat in shallow water areas, or in areas where you suspect

underwater obstacles may exist which could be struck by the

sterndrive or the boat bottom. The most important thing you can

do to help reduce injury or impact damage from striking a floating

or underwater object is to control the boat speed. Under these

conditions, boat speed should be kept to a minimum planing speed

24 to 40 km/h (15 to 25 MPH)

7462

Striking a floating or underwater object could result in an infinite

number of situations. Some of these situations could result in the

following:

• Part of the sterndrive or the entire sterndrive could break loose

and fly into the boat.

• The boat could move suddenly in a new direction. Such a

sharp change in direction can cause occupants to be thrown

out of their seats or out of the boat.

• A rapid reduction in speed. This will cause occupants to be

thrown forward, or even out of the boat.

• Impact damage to the sterndrive and/or boat.

Keep in mind, the most important thing you can do to help reduce

injury or impact damage during an impact is control the boat

speed. Boat speed should be kept to a minimum planing speed

when driving in waters known to have underwater obstacles.

Содержание HP700 SCi











































































































































Результаты поиска

Содержание HP700 SCi

Отзывы:

Mercury HP700 SCi, Руководство пользователя, Страница: 28 / 138

Результаты поиска

Содержание HP700 SCi

Отзывы: