GigaDevice Semiconductor GD32F403 Series страница 384 Скачать руководство пользователя

Страница: 384 / 711

GD32F403xx User Manual

384

11 and CH0MS bit-filed is 00(COMPARE MODE).

CH0COMSEN

Channel 0 compare output shadow enable

When this bit is set, the shadow register of TIMERx_CH0CV register, which updates

at each update event, will be enabled.

0: Channel 0 output co mpare shadow disable

1: Channel 0 output compare shadow enable

The PWM mode can be used without verifying the shadow register only in single

pulse mode (when SPM=1)

This bit cannot be modified when PROT [1:0] bit-filed in TIMERx_CCHP register is

11 and CH0MS bit-filed is 00.

CH0COMFEN

Channel 0 output compare fast enable

When this bit is set, the effect of an event on the trigger in input on the

capture/compare output will be accelerated if the channel is configured in PWM0 or

PWM1 mode. The output channel will treat an active edge on the trigger input as a

compare match, and CH0_O is set to the compare level independently from the

result of the comparison.

0: Channel 0 output quickly compare disable.

1: Channel 0 output quickly compare enable.

1:0

CH0MS[1:0]

Channel 0 I/O mode selection

This bit-field specifies the work mode of the channel and the input signal selection.

This bit-field is writable only when the channel is not active. (CH0EN bit in

TIMERx_CHCTL2 register is reset).).

00: Channel 0 is programmed as output mode

01: Channel 0 is programmed as input mode, IS0 is connected to CI0FE0

10: Channel 0 is programmed as input mode, IS0 is connected to CI1FE0

11: Channel 0 is programmed as input mode, IS0 is connected to ITS

Note:

When CH0MS[1:0]=11, it is necessary to select an internal trigger input

through TRGS bits in TIMERx_SMCFG register.

Input capture mode:

Bits

Fields

Descriptions

15:8

Reserved

Must be kept at reset value.

7:4

CH0CAPFLT[3:0]

Channel 0 input capture filter control

The CI0 input signal can be filtered by digital filter and this bit-field configure the

filtering capability.

Basic principle of digital filter: continuously sample the CI0 input signal according to

SAMP

and record the number of times of the same level of the signal. After reaching

the filtering capacity configured by this bit, it is considered to be an effective level.

The filtering capability configuration is as follows:

CH0CAPFLT [3:0]

Times

SAMP

4’b0000

Filter disabled.

Содержание GD32F403 Series








































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32F403 Series

Отзывы:

Похожие инструкции для GD32F403 Series

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32F403 Series, Руководство пользователя

Результаты поиска

Содержание GD32F403 Series

Отзывы:

Похожие инструкции для GD32F403 Series

Бренды по названию

Популярные бренды