GE Voluson 730Pro Скачать руководство пользователя страница 477

Страница: 477 / 480

Technical Data / Information

23.14 Tissue-Doppler

TD Mode:

Tissue mode flow imaging is only possible with phased array probes.

Display modes:

2D/TD (Single, Dual, Quad); 2D+2D/TD

TD coding steps:

8192 color steps

Depth range:

axial: 0 to B-scan range

lateral: 0 to B-scan-range

Zero line shift:

17 steps

Inversion of color direction:

yes

Smoothing Filter:

12 steps rising time

12 steps falling time

Gain control :

30dB

Density (color line density):

9 steps

Ensemble (color shots per line): 7 to 31
Pulse repetition frequency:

100 Hz to 11 kHz

TD Map:

4 different color codes for each probe

Frequency range:

1 to 15 MHz depending on the probe,

adjustable in 3 steps (low, mid, high)

Balance:

from 25 to 225 in 41 steps

Max. meas. velocity:

5.0 m/sec.

Min. meas. velocity:

0.3 cm/sec.

Display Mode:

V (velocity)

Scale:

kHz, cm/s, m/s

23.15 Power-Doppler

PD Mode:

Power-Doppler imaging is possible with curved array, linear array and phased array probes.

Display modes:

2D/PD (Single, Dual, Quad); 2D+2D/PD

Simultaneous triplex mode: 2D/PD+/D

3D/PD

PD coding steps:

256 color steps

PD window size:

lateral: maximum to minimum 2D mode scan angle

axial: 0 B-scan range

Display mode:

P (power)

Wall motion Filter:

7 steps

Smoothing Filter:

rising edge: 12 steps

falling edge: 12 steps

Gain control :

30dB

PD display ensemble:

7 to 31

PD display density

9 steps

Pulse repetition frequency:

100 Hz to 11kHz

PD Map:

8 different color codes for each probe

Frequency range:

1 to 15 MHz depending on the probe,

adjustable in 3 steps (low, mid, high)

Image sequence memory:

max. 128 images, 1024 images optional

Balance:

from 25 to 225 in 41 steps

Artifact suppression:

yes

Voluson

730Pro - Operation Manual

105831 Rev. 0

23-11

Содержание Voluson 730Pro
































































































































































































































































































































































































































































































Результаты поиска

Содержание Voluson 730Pro

Отзывы:

Похожие инструкции для Voluson 730Pro

Бренды по названию

Популярные бренды

GE Voluson 730Pro, Основное руководство пользователя

Результаты поиска

Содержание Voluson 730Pro

Отзывы:

Похожие инструкции для Voluson 730Pro

Бренды по названию

Популярные бренды