manualshive.com logo in svg

GE Voluson 730Pro, Основное руководство пользователя

GE Voluson 730Pro – мощный ультразвуковой аппарат для медицинских центров и ординаторий. Для обслуживания и настройки устройства, можно бесплатно скачать Руководство по обслуживанию с нашего сайта. Получите доступ к руководству на manualshive.com.

Поделиться
Скачать
background image

Calculations and Patient Reports

 

 

 

 

 

14.3.4.4 

To perform Fetal Doppler Measurements 

 

There are three methods of performing Fetal Doppler measurements in the Doppler spectrum: 

• 

Auto Trace

 

(chapter 14.3.4.4.1)

 

• 

Manual Trace

 

(chapter 14.3.4.4.2)

 

• 

Measurement of Each Item

 

(chapter 14.3.4.4.3)

 

• 

To measure Fetal Heart Rate

 

(chapter 14.3.4.4.4)

 

 
 
 
 

14.3.4.4.1 Auto 

Trace 

 
1.  After obtaining a feasible Doppler spectrum, press the 

[

Calc

]

 key on the control panel. 

The OB Calculations menu appears in the menu area. 

 

2.  Select the appropriate “Measure Group” and select 

[

Auto Trace

]

. 

 
The Doppler spectrum is traced automatically and the results are 
displayed. 
 

 
3.  Select the sensitivity of the envelope curve  

(to eliminate artifacts). 
 

 

4.  Select the Trace Mode channel of the envelope 

curve (upper, both or lower). 
 

 

A green line appears at the left of the spectrum.  
Press the upper trackball key 

[

Change

]

 to move the line and readjust 

the start cycle (the line changes to yellow).Press the right or left 
trackball key 

[

Set

]

 to fix the line. 

A green line appears at the right of the spectrum. Press the 

[

Change

]

 

key again (line changes to yellow), move the line to readjust the end 
cycle and fixate it with 

[

Set

]

. 

 

 
The status area shows the current function of the trackball. 
If you press the right or left trackball key 

[

Store

]

, the measurement results are 

stored in the OB report. 

 
 
 

Important note:

 

The determination of the envelope curve requires a clear and low-noise recording of the Doppler 
spectrum. Otherwise the reliability of the displayed measurement results may not be ensured!

 

 

 

  

Voluson

®

 730Pro  -  Basic User Manual 

14-14

 

 

105831   Rev. 0

 

Содержание Voluson 730Pro

































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Voluson 730Pro

Campden instruments 7600 Series Instruction Manual preview
7600 Series
Бренд: Campden instruments Страницы: 8
Febco 860 Series Maintenance Manual preview
860 Series
Бренд: Febco Страницы: 12
Yetter 5500 Series Owner'S Manual, Part Identification preview
5500 Series
Бренд: Yetter Страницы: 16
Tascam CD-RW5000 Owner'S Manual preview
CD-RW5000
Бренд: Tascam Страницы: 27
Jay-Lor A50 Owner'S Manual preview
A50
Бренд: Jay-Lor Страницы: 72
MacDon TM100 Manual preview
TM100
Бренд: MacDon Страницы: 198
M-Triangel M1 Operating Instruction preview
M1
Бренд: M-Triangel Страницы: 6
GALBIATI PRIMA Quick Manual preview
PRIMA
Бренд: GALBIATI Страницы: 20
Oakworks Medical PG Series Instruction & Maintenance Manual preview
PG Series
Бренд: Oakworks Medical Страницы: 28
Össur bionic power knee Quick Reference Card preview
bionic power knee
Бренд: Össur Страницы: 2
Össur BALANCE KNEE OM8 Instructions For Use Manual preview
BALANCE KNEE OM8
Бренд: Össur Страницы: 36
Össur BALANCE FOOT J Instructions For Use Manual preview
BALANCE FOOT J
Бренд: Össur Страницы: 37
Össur REBOUND DIABETIC WALKER Instructions For Use Manual preview
REBOUND DIABETIC WALKER
Бренд: Össur Страницы: 63
Össur UNITY Instructions For Use Manual preview
UNITY
Бренд: Össur Страницы: 67
Électronique du Mazet ECHODIA Babyscreen Instructions For Use And Technical Description preview
ECHODIA Babyscreen
Бренд: Électronique du Mazet Страницы: 65
Zodiac Sheer Descent Installation And Operation Manual preview
Sheer Descent
Бренд: Zodiac Страницы: 32
Omcan 47350 Instruction Manual preview
47350
Бренд: Omcan Страницы: 20
Meritor RS 120 Maintenance Manual preview
RS 120
Бренд: Meritor Страницы: 65

Бренды по названию

Популярные бренды

Загрузить еще бренды