GE Voluson 730Pro Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 480

background image

Safety

2.4

Remarks for Safe Use

* Get acquainted with the transducers and the ultrasound system: read the user manual thoroughly!

* Follow these safety instructions as well as the clinically adopted precautions and measures for

hygiene.

* The manufacturer is not liable for damage caused by improper or inexpert use of the device!

* Any ultrasound transducers - irrespective of system and design - are sensitive to shock and shall be

treated with care. Pay attention to cracks which may allow conductive fluids to leak in.

* Any type of repair shall only be performed by authorized personnel. Never attempt to open a

transducer or transducer connector. This leads to a loss of guarantee!

* Avoid kinking, bending or twisting of probe cables and take care to guard them against mechanical

stress (e.g., wheels or heels).

*  The probes must not be exposed to mechanical shock (e.g., by dropping).
  Any damage caused in this manner invalidates warranty.

*  Have the scanner system and the transducers regularly checked (for faulty cables, housing, etc.) by

authorized personnel!

* Damage to transducer or cable may lead to a safety hazard, therefore have them repaired

immediately!

* Before plugging in or unplugging a transducer, activate the "FREEZE" mode.

* Installation and first switch-on and check-up of the system shall be performed by a specialist

acquainted with the handling and use of the system.

*  The user must have read and understood the user manual.
  The system must only be operated by trained and qualified personnel.

*  For safety reasons, avoid handling fluids in the vicinity of the system. Fluids leaking into the disk

drive can damage the drive. Never remove the storage shelf above the probe connectors, it helps to
protect the unit from fluids.

* Do not put your hand under the control console when moving it: Danger of injuries!

* Trolley: never move the unit with blocked wheels, but block the wheels in the proximity of stairs

and ramps.

* Place the unit always on horizontal ground and block the front wheels: Danger of tipping over and

rolling away.

*  In transporting the system, raise the foot rest: Danger of injuries!

*  The user manual must always be with the scanner system. It is the user's duty to ensure this!

*  Only probes conforming to type BF requirements may be used with the VOLUSON

®

730Pro.

See the probe's label. In case of doubt ask authorized service personnel.

Voluson

®

730Pro - Basic User Manual

105831 Rev. 0

2-5

«
...
27
28
29
30
31
...
»

Содержание Voluson 730Pro

































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Voluson 730Pro

Бренд: Salvis Страницы: 40

Бренд: IDEAL Страницы: 2

Бренд: GE Страницы: 242

Бренд: GE Страницы: 24

Бренд: Balanced Body Страницы: 3

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: h/p/cosmos Страницы: 81

Smart Plus PHT-35LHS

Бренд: Vatech Страницы: 190

Бренд: Harken Страницы: 4

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды