INSTRUCTIONS
V
™
Blocks
N15W24983 Bluemound Road • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008 • Web: harken.com • E-mail: [email protected]
You Must Supply
1. Primary support loop or lashing line
Harken is not liable or responsible for choosing line used to secure blocks. Go
to Harken Limited Warranty at www.harken.com/manuals for complete details.
Refer to the “Specifications Chart” above and use a loop/lashing with a
maximum working load that meets or exceeds the maximum working load
listed. If working with breaking loads, use a breaking load that is four (4) times
the maximum working load listed.
Important information on choosing line, knots, and splices:
See www.harken.com/knots.
2. Secondary lashing line
Use a small diameter line for lashing the primary supporting loop or lashing
near the head. Line length and diameter will vary depending on block.
WARNING! Knots weaken line considerably. Work with a qualified
rigger or line manufacturer on securing line. Select high-strength
loops using the instructions in “1” at left, or consult rigger for
recommendations on lashing.
Specifications
Note: See replacement part numbers on last page.
Mouth
Ø
WARNING! Strictly follow all instructions to avoid an accident, damage to your vessel,
personal injury or death. See www.harken.com/manuals for additional safety information.
= Incorrect. Avoid to prevent accidents.
V blocks mount using soft attachment methods. The primary support lashings or loops pass through the block's mouth. A secondary lashing keeps the block
aligned. Cheeks are 3D-molded carbon or machined aluminum. The bearing system combines axial and thrust bearings into a single bearing set of angled
titanium rollers.
Sheave diameter
Max line Ø
Mouth Ø
Maximum working load
Breaking load
Part No.*
Description
mm
in
mm
in
mm
in
kg
lb
kg
lb
3294, 3294AL
1.5T single
47
1.85
9
11/32
15
.59
1500
3300
3000
6600
3366AL
1.5T wide
47
1.85
2x 9
2x 11/32
15
.59
1500
3300
3000
6600
3295, 3295AL
3.0T single
56
2.20
11
7/16
20
.785
3000
6600
6000
13200
3367AL
3.0T wide
56
2.20
2X 11
2X 7/16
20
.785
3000
6600
6000
13200
3296, 3296AL
5.0T single
62
2.44
13
1/2
20
.785
5000
11000
10000
22000
3362AL
5.0T wide
62
2.44
2X 14
2X 9/16
20
.785
5000
11000
10000
22000
3297, 3297AL
6.5T single
82
3.23
16
5/8
26
1.02
6500
14300
13000
28600
3368AL
6.5T wide
82
3.23
2X 16
2X 5/8
26
1.02
6500
14300
13000
28600
3363AL
8T single
104
4.09
18
11/16
42
1.67
8000
17600
16000
35200
3369AL
8T wide
104
4.09
2X 18
2X 11/16
42
1.67
8000
17600
16000
35200
3370AL
12T single
120
4.75
22
7/8
51
2.03
12000
26400
24000
52800
3371AL
16T single
140
5.5
26
1 1/16
63
2.49
16000
35200
32000
70400
3372AL
20T single
155
6.13
30
1 3/16
64
2.52
20000
44000
40000
88000
*Block cheeks are carbon or aluminum. AL signifies aluminum cheeks.
Head
Mouth
Cheek
Sheave
Primary support
loop or lashing
Secondary
lashing
Terms
Carbon and Aluminum V Blocks
Secondary
lashing
tunnel
#5097 Manual
4 pages, Print booklet style
Black ink only
Prints both sides
40# Offset stock
11x17" folded as indicated
