GE Voluson 730Pro Скачать руководство пользователя страница 424 | Manualshive

Страница: 424 / 480

background image

Probes and Biopsy

20.10.4 Mechanical Hazards

A defective probe or excessive force can cause patient injury or probe damage:

•

Observe depth markings and do not apply excessive force when inserting or
manipulating intracavitary probes.

•

Inspect probes for sharp edges or rough surfaces that could injure sensitive

tissue.

20.11 Special Handling Instructions

20.11.1 Using Protective Sheaths

Protective barriers may be required to minimize disease transmission. Probe
sheaths are available for use with all clinical situations where infection is a
concern. Use of legally marketed, sterile probe sheaths is strongly
recommended for intracavitary and intraoperative procedures. Use of legally
marketed, sterile, pyrogen free probe sheaths is REQUIRED for neurological
intra-operative procedures.

Instructions:

Custom-made sheaths are available for each probe. Each

probe sheath kit consists of a flexible sheath used to cover the probe and
cable and elastic bands used to secure the sheath.

Sterile probe sheaths are supplied as part of biopsy kits for those probes
intended for use in biopsy procedures. In addition to the sheath and elastic
bands, there are associated accessories for performing a biopsy procedure
which are included in the kit.
Refer to the biopsy instructions for the specific probes in the Discussion
section of this chapter for further information.

Reordering:

To reorder sheaths, refer to Ultrasound Probe and Cord Sheath

Sets (continued).

Devices containing latex may cause severe allergic reaction in latex sensitive
individuals.
Refer to FDA's March 29, 1991 Medical Alert on latex products.

DO NOT

use pre-lubricated condoms as a sheath.

In some cases, they may damage the probe. Lubricants in these condoms may
not be compatible with probe construction.

DO NOT

use an expired probe sheath.

Before using probe sheaths, verify whether the term of validity has expired.

Voluson

®

730Pro - Basic User Manual

20-10

105831 Rev. 0

«
...
422
423
424
425
426
...
»

Содержание Voluson 730Pro

































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Voluson 730Pro

Бренд: Datalogic Страницы: 48

Бренд: PageFlip Страницы: 32

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: ubicquia Страницы: 4

Бренд: Fagor Страницы: 92

Бренд: Kanlux Страницы: 4

Portable Vocal Booth Pro Studio Series

Бренд: EditorsKeys Страницы: 2

Calculite C6P38MHA

Бренд: Lightolier Страницы: 2

Бренд: Turner Designs Страницы: 55

Бренд: Chauvin Arnoux Страницы: 12

Бренд: EMIT Страницы: 6

Бренд: ADJ Страницы: 6

Бренд: BERRIDGE Страницы: 11

Бренд: Helmer Страницы: 18

Бренд: Air Techniques Страницы: 32

OT LED Area Light Series

Бренд: SolarMax Страницы: 2

Бренд: Venue Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды