GE Voluson 730Pro Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 480

background image

CFM Mode

8.3.6 Baseline

The CFM baseline shift can be used to prevent aliasing in one flow direction similar to the PW
Doppler baseline shift. Shifting the CFM baseline enlarges the velocity range in one direction.
The zero line of the color bar is also shifted.

There are

8 Steps in each direction.

By step 8 you see only the color wedge in one direction (maximum velocity), the other
direction is 0 (kHz, cm/s , m/s).

Only possible in Display Mode V, V-T and V-Pow

The maximum value and minimum value of the flow velocities are displayed at the upper and lower
edge of the color wedge.

8.3.7 Ensemble

This function controls the number of pulses for one displayed Color-Doppler line. Since several pulses
are to be evaluated for display of a result, the color display quality increases with the number of
evaluated pulses.

Switch the

[

Ensemble

]

key and select the number of pulses per color line.

max. value:

31

min. value:

7

step size:

1

Switch up or down to increase or decrease the number of pulses per color line.
With increasing CFM Ensemble the frame rate decreases.

Remark:

Changes are only possible in write mode!

8.3.8 Line

Density

This function determines the line density within the CFM box. The lower the line density, the greater
the distance between lines and the size of the color pixels.

Switch the

[

Line D.

]

key and adjust the line density.

Switch up or down to increase or decrease the line density.

max. value:

9

min. value:

1

step size:

1

Remark:

Changes are only possible in write mode.

Voluson

®

730Pro - Basic User Manual

105831 Rev. 0

8-13

«
...
153
154
155
156
157
...
»

Содержание Voluson 730Pro

































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Voluson 730Pro

Бренд: Campden instruments Страницы: 8

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: Cambro Страницы: 6

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: Hammer Страницы: 42

Бренд: Nederman Страницы: 255

Бренд: KCI Страницы: 2

Бренд: KCI Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды