GE Voluson 730Pro Скачать руководство пользователя страница 284 | Manualshive

Страница: 284 / 480

background image

Basic Measurements

13.4.5

3D MultiPlane Measurement

This measuring program allows for volume determination of any organ which was stored by a volume
scan. Several parallel planes are laid through the organ and the areas of these planes are determined.
A measuring program calculates the volume from the measured areas and the distance between the
areas. The larger the number of areas, the more exact the volume calculation result will be.

Condition: A stored volume scan (Sectional Planes view).

To measure volume using the MultiPlane method.

1. Select the reference image in which the measurement is to be performed. (A, B or C)

2. Select

the

[

MultiPlane

]

item. The menu area changes to the 3D MultiPlane menu.

3. Select the first section through the body by rotating the

[

Ref. Slice

]

digipot

(make parallel sections through the reference image).

Note:

The first section should be set at the edge of the measured object.

4. Measure the area (proceed as for area measurement).

Position the start dot of the area to be surrounded with the trackball and store it. Surround the area
with the trackball, then press the right or left trackball key

[

Set

]

.

The area is calculated and displayed. The area may even be "zero" (dot at the edge).

5. Touch the key

[

Set

]

twice

!

6. Select the next parallel section with the

[

Ref. Slice

]

digipot and measure the area.

7. Repeat 5. and 6. until the edge of the measured object is reached.

Remarks:

•

The contour of the measured area is not erased if a new section is adjusted. From the deviation in
the new section it is possible to decide whether a new area should be marked.
With new marking the old contour is erased.

•

To call back the measured areas touch the

[

Prev / Next

]

flip switch.

•

The different sections can be chosen liberally, it is not necessary to follow a certain order.

•

The volume measurement is only possible in 3D mode or full-image mode (not in aspect mode).

•

To erase results, select the

[

Init

]

item.

Voluson

®

730Pro - Basic User Manual

13-10

105831 Rev. 0

«
...
282
283
284
285
286
...
»

Содержание Voluson 730Pro

































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Voluson 730Pro

Бренд: Bahco Страницы: 9

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Бренд: Össur Страницы: 98

Flex Foot Cheetah

Бренд: Össur Страницы: 107

Бренд: Össur Страницы: 38

Бренд: Össur Страницы: 39

Bionic Symbionic Leg

Бренд: Össur Страницы: 2

Бренд: Össur Страницы: 67

Бренд: Össur Страницы: 17

Бренд: JBM Страницы: 12

PulseDose LT PD1000

Бренд: DeVilbiss Страницы: 58

Бренд: Game Winner Страницы: 25

LIGHTHOUSE SPORT 3.18

Бренд: Raymarine Страницы: 162

CarePump Lite 6

Бренд: BARDOMED Страницы: 34

Бренд: EFILive Страницы: 39

SKINGUARD Series

Бренд: KAP Medical Страницы: 39

INSTINCT ROTARY TORSO

Бренд: Nautilus Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды