GE Voluson 730Pro Скачать руководство пользователя страница 431 | Manualshive

Страница: 431 / 480

background image

Probes and Biopsy

20.12.3 Disinfecting

Probes

Ultrasound probes can be disinfected using liquid chemical germicides. The level of disinfection is
directly related to the duration of contact with the germicide. Increased contact time produces a higher
level of disinfection.
Cidex and Sporox are the only germicides approved by GE Medical Systems for Ultrasound probe
disinfecting purposes. 2% Glutaraldehyde-based solutions (Cidex) have been shown to be very
effective for disinfecting.

Please consider our constantly updated Care-Card (which is inside the transducer boxes) for
compatible disinfectants and gels !

You also find this information on the web:

The Care website will be at

http://www.geultrasound.com/

and

http://www.gemedicalsystems.com/

To reach the Care and disinfectant listing site please select

Radiology -

Ultrasound - Probes!

In order for liquid chemical germicides to be effective, all visible residue must be
removed during the cleaning process. Thoroughly clean the probe, as described
earlier, before attempting disinfection.

1. Prepare the germicide solution according to the manufacturer's instructions. Be sure to follow all

precautions for storage, use and disposal.

2. Place the cleaned and dried probe in contact with the germicide for the time specified by the

germicide manufacturer. High-level disinfection is recommended for surface probes and is
required for endocavitary and intraoperative probes (follow the germicide manufacturer's
recommended time).

3. After removing from the germicide, rinse the probe following the germicide manufacturer's

rinsing instructions. Flush all visible germicide residue from the probe and allow to air dry.

CREUTZFIELD-JACOB DISEASE

Neurological use on patients with this disease must be avoided.

If a probe becomes contaminated, there is no adequate disinfecting means.

Voluson

®

730Pro - Basic User Manual

105831 Rev. 0

20-17

«
...
429
430
431
432
433
...
»

Содержание Voluson 730Pro

































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Voluson 730Pro

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: Kapriol Страницы: 32

Бренд: iGuzzini Страницы: 20

Бренд: Xoop Lighting Страницы: 20

Бренд: Vari Lite Страницы: 132

Бренд: CAIRE Страницы: 2

Бренд: AAON Страницы: 36

Бренд: Bacharach Страницы: 48

Бренд: Rangevision Страницы: 28

Бренд: Cambro Страницы: 6

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 15

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды