manualshive.com logo in svg

GE LOGIQ A3, Базовое руководство по обслуживанию

GE LOGIQ A3 - базовый сервисный мануал доступен для бесплатного скачивания с нашего сайта. В этом руководстве вы найдете все необходимые инструкции для обслуживания вашего прибора. Посетите manualshive.com для загрузки.

Поделиться
Скачать
background image

GE H

EALTHCARE

D

IRECTION

 5213326-100, R

EVISION

 3 

LOGIQ™ A3 S

ERVICE

 M

ANUAL

 

10-10

Section 10-5 - System Maintenance

10-5-4-3

Physical Inspection

 

Table 10-12   Physical Checks

Step

Item

Description

1

Labeling

Verify that all system labeling is present and in readable condition.

2

Scratches & Dents Inspect the console for dents, scratches or cracks.

3

Control Panel

Inspect keyboard and control panel. Note any damaged or missing items.

4

Control Panel 

Movement

Verify ease of control panel (Operator I/O Panel) movement in all acceptable directions. Ensure that 
it latches in position as required.

5

Wheels & Brakes

Check all wheels and casters for wear and verify operation of foot brake, to stop the unit from moving, 
and release mechanism. Check all wheel locks and wheel swivel locks for proper operation.

6

Cables & 

Connectors

Check all internal cable harnesses and connectors for wear and secure connector seating. Pay 
special attention to footswitch assembly and probe strain or bend reliefs.

7

Shielding & 

Covers

Check to ensure that all EMI shielding, internal covers, air flow panels and screws are in place. 
Missing covers and hardware could cause EMI/RFI problems while scanning.

8

External I/O

Check all connectors for damage and verify that the labeling is good.

State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process. 

See the GEHC Myworkshop System to determine the status of this document.

Approved Document - 5213326-100TPH_r3.pdf Page 233 of 252

Содержание LOGIQ A3





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LOGIQ A3

Rabe TURBOSEED PRO Original Instructions Manual preview
TURBOSEED PRO
Бренд: Rabe Страницы: 65
Landoll 850 Series Supplement Manual preview
850 Series
Бренд: Landoll Страницы: 6
ParaBody 827 Assembly Instruction Sheet preview
827
Бренд: ParaBody Страницы: 9
ParaBody 828 Assembly Instructions preview
828
Бренд: ParaBody Страницы: 3
MacDon 802 Operator'S Manual preview
802
Бренд: MacDon Страницы: 45
H&S 8200 Series Operator'S Manual preview
8200 Series
Бренд: H&S Страницы: 30
Napoleon S1 Assembly Replacement Instructions preview
S1
Бренд: Napoleon Страницы: 2
Raytheon V800 Instruction Manual preview
V800
Бренд: Raytheon Страницы: 62
EWM Tetrix 351 AC/DC Smart FW Operating Instructions Manual preview
Tetrix 351 AC/DC Smart FW
Бренд: EWM Страницы: 117
Nautilus HDP6D-LFHR Assembly Manual preview
HDP6D-LFHR
Бренд: Nautilus Страницы: 12
CAIRE SPRINT User Manual preview
SPRINT
Бренд: CAIRE Страницы: 16
ZIGBEE 622 Quick Start Manual preview
622
Бренд: ZIGBEE Страницы: 6
Daisy DMR Installation Manual preview
DMR
Бренд: Daisy Страницы: 2
Daisy Below Ground Pool Cover Box Installation Manual preview
Below Ground Pool Cover Box
Бренд: Daisy Страницы: 3
idi MDS Installation & Operator'S Manual preview
MDS
Бренд: idi Страницы: 20
G&G FPX Series Installation Manual preview
FPX Series
Бренд: G&G Страницы: 2
H&S 5226 Operator'S Manual preview
5226
Бренд: H&S Страницы: 46
JB-Lighting P18 Operating Instructions Manual preview
P18
Бренд: JB-Lighting Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды