GE LOGIQ A3 Скачать руководство пользователя страница 97

Страница: 97 / 252

GE H

EALTHCARE

IRECTION

5213326-100, R

EVISION

LOGIQ™ A3 S

ERVICE

ANUAL

4-10

Section 4-4 - Functional Checks

4-4-6

Probe/Connectors Usage

4-4-6-1

Connecting a probe

1.) Place the probe's carrying case on a stable surface and open the case.

2.) Carefully remove the probe and unwrap the probe cable.

3.) DO NOT allow the probe head to hang free. Impact to the probe head could result in irreparable

damage.

4.) Turn the connector locking handle counterclockwise.

5.) Align the connector with the probe port and carefully push into place.

6.) Turn the connector locking handle clockwise to secure the probe connector.

7.) Carefully position the probe cable in the probe cord holder spot so it is free to move, but not

resting on the floor.

4-4-6-2

Activating the probe

Press

“Probe”

Key available on the control panel. The next available probe will be actiavetd and

presets will be loaded automatically.

When deactivating the probe, the probe is automatically placed in standby mode.

1.) Press the

Freeze

key.

2.) Gently wipe the excess gel from the face of the probe. (Refer to the Basic User Manual for

complete probe cleaning instructions.)

3.) Carefully slide the probe around the right side of the keyboard, toward the probe holder.

Ensure that the probe is placed gently in the probe holder.

4-4-6-3

Disconnecting the probe

Probes can be disconnected at any time. However, the probe should not be selected as the active
probe.

1.) Move the probe locking handle counterclockwise. Pull the probe and connector straight out of

the probe port.

2.) Carefully slide the probe and connector away from the probe port and around the right side of

the keyboard. Ensure the cable is free.

3.) Be sure that the probe head is clean before placing the probe in its storage box.

State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.

See the GEHC Myworkshop System to determine the status of this document.

Approved Document - 5213326-100TPH_r3.pdf Page 97 of 252

Содержание LOGIQ A3





























































































































































































































































Результаты поиска

Содержание LOGIQ A3

Отзывы:

Похожие инструкции для LOGIQ A3

Бренды по названию

Популярные бренды

GE LOGIQ A3, Базовое руководство по обслуживанию

Результаты поиска

Содержание LOGIQ A3

Отзывы:

Похожие инструкции для LOGIQ A3

Бренды по названию

Популярные бренды