GE LOGIQ A3 Скачать руководство пользователя страница 89

Страница: 89 / 252

GE H

EALTHCARE

IRECTION

5213326-100, R

EVISION

LOGIQ™ A3 S

ERVICE

ANUAL

4-2

Section 4-3 - General Procedure

Section 4-3General Procedure

4-3-1

Power On/Boot Up

For Power On/Off process , Refer Power On / Off Process on page 3 - 14

4-3-2

Adjusting the Display Monitor

4-3-2-1

Brightness and Contrast

To adjust the brightness:

1.) Press the menu button of the display.

2.) Press the “+” button to increase brightness.

Press the “-” to decrease brightness.
The amount of brightness is shown on a slider on the screen.

To adjust the contrast:

1.) Press the menu button of the display. Select the contrast from the popup menu.

2.) Press the “+” button to increase contrast.

Press the “-” to decrease contrast.
The amount of the contrast is shown on a slider on the screen.

4-3-3

Lockout/Tagout Requirements (For USA/Europe Only)

Follow OSHA Lockout/Tagout requirements by ensuring you are in total control of the plug.

CAUTION

SYSTEM REQUIRES ALL COVERS
Operate this unit only when all board covers and frame panels are securely in place. The
covers are required for safe operation, good system performance and cooling purposes.

NOTICE

Lockout/Tagout Requirements (For USA only)

Follow OSHA Lockout/Tagout requirements by ensuring you are in total control of the Power Cable
on the system.

NOTICE

Lockout/Tagout Requirements (For USA / Europe only)

Follow OSHA Lockout/Tagout requirements by ensuring you are in total control of the Power Cable
on the system.

Signed

Date

TAG

LOCKOUT

Signed

Date

TAG

LOCKOUT

State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.

See the GEHC Myworkshop System to determine the status of this document.

Approved Document - 5213326-100TPH_r3.pdf Page 89 of 252

Содержание LOGIQ A3





























































































































































































































































Результаты поиска

Содержание LOGIQ A3

Отзывы:

Похожие инструкции для LOGIQ A3

Бренды по названию

Популярные бренды

GE LOGIQ A3, Базовое руководство по обслуживанию

Результаты поиска

Содержание LOGIQ A3

Отзывы:

Похожие инструкции для LOGIQ A3

Бренды по названию

Популярные бренды