GE LOGIQ A3 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 252

background image

GE H

EALTHCARE

D

IRECTION

5213326-100, R

EVISION

3

LOGIQ™ A3 S

ERVICE

M

ANUAL

1-2

Section 1-2 - Safety

Section 1-1 Overview

1-1-4

Typical Users of the Basic Service Manual

•

Service Personnel (installation, maintenance, etc.).

•

Hospital’s Service Personnel

•

Contractors (Some parts of Chapter - Pre-Installation)

1-1-5

Purpose of Operator Manual(s)

The Operator Manual(s) should be fully read and understood before operating the LOGIQ A3 and also
kept near the unit for quick reference.

Section 1-2Safety

1-2-1

Warnings

1.) The operator manual should be fully read and understood before operating the LOGIQ A3 and kept

nearby for quick reference.

2.) Although the ultrasound energy transmitted from the LOGIQ A3 transducer is within AIUM/NEMA

standards, unnecessary exposure should be avoided. Only trained personnel should operate the
LOGIQ A3.

3.) To prevent electrical shock, the LOGIQ A3 should be connected to a properly grounded power

receptacle. Do not use a three prong to two prong adapter. This defeats safety grounding.

4.) Probes are fragile, please handle with care.

5.) Concerning Outside Markings, refer to Figure

through

.

6.) For the cleaning, disinfection, and sterilization, refer to Probe section in LOGIQ A3 User Manual

and Caution Sheet supplied with each probe.

WARNING

WARNING

CAREFULLY READ ALL OF THE WARNINGS BELOW

NOTICE

This medical equipment is approved, in terms of the prevention of radio wave interference, to be used
in hospitals, clinics and other institutions which are environmentally qualified. The use of this equipment
in an inappropriate environment may cause some electronic interference to radios and televisions
around the equipment. Proper handling of this equipment is required in order to avoid such trouble
according to the operator and service manuals.This equipment can be used in residential areas only
under the supervision of physicians or qualified technicians.

CAUTION

Improper performance possibility. Do not use the following devices near this equipment.
Cellular phone, radio transceiver, mobile radio transmitter, radio-controlled toy, etc. Use of
these devices near this equipment could cause this equipment to perform outside the published
specifications. Keep power to these devices turned off when near this equipment

State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.

See the GEHC Myworkshop System to determine the status of this document.

Approved Document - 5213326-100TPH_r3.pdf Page 31 of 252

«
...
29
30
31
32
33
...
»

Содержание LOGIQ A3





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LOGIQ A3

Бренд: ACS Страницы: 56

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: NARGESA Страницы: 50

Бренд: Oberheim Страницы: 40

Бренд: Unex Страницы: 5

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: ADVANCED HOME CARE Страницы: 16

Бренд: Panta Safe Light Страницы: 2

Бренд: Calrec Страницы: 70

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Qu-Bit Electronix Страницы: 15

RIDA qLine ZG2601

Бренд: R-Biopharm Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды