GE LOGIQ A3 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 252

background image

GE H

EALTHCARE

D

IRECTION

5213326-100, R

EVISION

3

LOGIQ™ A3 S

ERVICE

M

ANUAL

1-8

Section 1-4 - Safety Considerations

1-4-4

Electrical Safety

To minimize shock hazard, the equipment chassis must be connected to an electrical ground. The
system is equipped with a three-conductor AC power cable. This must be plugged into an approved
electrical outlet with safety ground. If an extension cord is used with the system, make sure that the total
current rating of the extension cord is greater than the system rating.

The power outlet used for this equipment should not be shared with other types of equipment.

Both the system power cable and the power connector meet international electrical standards.

1-4-5

Returning/Shipping Probes and Repair Parts

Equipment being returned must be clean and free of blood and other infectious substances.

GEMS policy states that body fluids must be properly removed from any part or equipment prior to
shipment. GEMS employees, as well as customers, are responsible for ensuring that parts/equipment
have been properly decontaminated prior to shipment. Under no circumstance should a part or equip-
ment with visible body fluids be taken or shipped from a clinic or site (for example, body coils or an
ultrasound probe).

The purpose of the regulation is to protect employees in the transportation industry, as well as the peo-
ple who will receive or open this package.

NOTE:

The US Department of Transportation (DOT) has ruled that “items that were saturated and/or
dripping with human blood that are now caked with dried blood; or which were used or intended
for use in patient care” are “regulated medical waste” for transportation purposes and must be
transported as a hazardous material.

CAUTION

If the Power Plug is Modified or replaced to Suit the local Conditions and regulations, Ground
continuity check should be performed between Ground Pin on the Plug and a Metal Part on the
LOGIQ A3.

State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.

See the GEHC Myworkshop System to determine the status of this document.

Approved Document - 5213326-100TPH_r3.pdf Page 37 of 252

«
...
35
36
37
38
39
...
»

Содержание LOGIQ A3





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LOGIQ A3

Бренд: Kapriol Страницы: 32

Бренд: NEC Страницы: 44

Бренд: Ultimaker Страницы: 38

Бренд: A&D Страницы: 2

Бренд: A&D Страницы: 176

Бренд: Daga Страницы: 24

Бренд: DAF Страницы: 68

Бренд: XanLite Страницы: 4

Бренд: iHealth Страницы: 8

Бренд: Parkside Страницы: 95

Бренд: ZOLL Страницы: 37

Бренд: Wacker Neuson Страницы: 34

Бренд: Wagan Страницы: 4

Бренд: Wachs Страницы: 22

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

ZA top SM315.100A

Бренд: ZIEHL-ABEGG Страницы: 76

FLOOReco 5164-040120

Бренд: DOTLUX Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды