GE LOGIQ A3 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 252

background image

GE H

EALTHCARE

D

IRECTION

5213326-100, R

EVISION

3

LOGIQ™ A3 S

ERVICE

M

ANUAL

Chapter 2

2-3

2-2-2

Electrical Requirements

NOTE:

GE Medical Systems requires a dedicated power and ground for the proper operation of its
Ultrasound equipment. This dedicated power shall originate at the last distribution panel before
the system.

Sites with a mains power system with defined Neutral and Live:

The dedicated line shall consist of one phase, a neutral (not shared with any other circuit), and a full
size ground wire (not shared with any other circuit) from the distribution panel to the Ultrasound outlet.

Sites with a mains power system without a defined Neutral:

The dedicated line shall consist of one phase (two lines), not shared with any other circuit, and a full
size ground wire (not shared with any other circuit) from the distribution panel to the Ultrasound outlet.

NOTE:

Please note that image artifacts can occur, if at any time within the facility, the ground from the
main facility's incoming power source to the Ultrasound unit is only a conduit.

2-2-3

Power Requirements

Electrical Specifications for LOGIQ A3.

2-2-3-1

Inrush Current

Inrush current is not a factor to consider due to inrush current limiting properties of the power supplies.

2-2-3-2

Site Circuit Breaker

It is recommended that the branch circuit breaker for the machine be ready accessible.

2-2-3-3

Site Power Outlets

A dedicated AC power outlet must be within reach of the unit without extension cords. Other outlets
adequate for the external peripherals, medical and test equipment needed to support this unit must also
be present within 1 m (3.2 ft.) of the unit. Electrical installation must meet all current local, state, and
national electrical codes.

PARAMETER

AREA

LIMITS

Voltage Range

230V

230 VAC

±

10% (207-253 VAC)

Voltage Range

120V

120 VAC

±

10% (103-127 VAC)

Power

All applications

MAX. 425VA

Line Frequency

All applications

50/60Hz (

±

2Hz)

Power Transients

All applications

Less than 25% of nominal peak voltage
for less than 1 millisecond for any type of
transient, including line frequency,
synchronous, asynchronous, or
aperiodic transients.

Decaying Oscillation

All applications

Less than 15% of peak voltage for less
than 1 millisecond.

Table 2-4

Electrical Specifications for LOGIQ A3

DANGER

POWER OUTAGE MAY OCCUR.
The LOGIQ A3 requires a dedicated single branch circuit. To avoid circuit overload and
possible loss of critical care equipment, make sure you DO NOT have any other equipment
operating on the same circuit.

State: RELEASE - Document is released and under formal Change Control. Changes are subject to the ECR/ECO Process.

See the GEHC Myworkshop System to determine the status of this document.

Approved Document - 5213326-100TPH_r3.pdf Page 52 of 252

«
...
50
51
52
53
54
...
»

Содержание LOGIQ A3





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LOGIQ A3

Бренд: THORLABS Страницы: 44

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: Panasonic Страницы: 9

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: XM Fitness Страницы: 10

Бренд: Federal Signal Corporation Страницы: 4

Бренд: FASTERHOLT Страницы: 96

Бренд: Qlight Страницы: 4

Бренд: KAM Страницы: 5

Бренд: Jenx Страницы: 34

Бренд: B+S Страницы: 16

Бренд: Bondura Страницы: 10

Бренд: Hill-Rom Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды