manualshive.com logo in svg

Danfoss VLT AutomationDrive FC 301, Руководство по программированию, Страница: 253 / 722

Поделиться
Скачать
Danfoss VLT AutomationDrive FC 301 Скачать руководство пользователя страница 253

•
•

•

-
-

•
•
•

5.8 Parameter Group 7-** Controllers

5.8.1 Speed PID Droop

This feature implements precise torque sharing between multiple motors on a common mechanical shaft. Speed PID droop is useful
for marine and mining applications where redundancy and higher dynamics are required. Speed PID droop allows to reduce inertia
by utilizing multiple small motors instead of 1 large motor.

e3

0b

e1

97

.1

1

Set-point

Calculation

External Set-point

Ramp

Droop

Speed

PID

Torque

PID

M2

M3

Drive 2

Drive 3

Set-point

Calculation

Ramp

Droop

Speed

PID

-

Set-point

Calculation

Ramp

Droop

Speed

PID

Torque

PID

M1

Drive 1

-

-

Torque

PID

Illustration 72: Concept of Speed PID Droop

The value in 

parameter 7-01 Speed PID Droop

 ensures that the load is shared equally between the motors. If the torque on the motor

is 100% of nominal motor torque, the drive reduces its output to this motor by 100% of the value in 

parameter 7-01 Speed PID Droop

.

If the torque is 50% of nominal motor torque, the drive reduces its output to this motor by 50% of the value in 

parameter 7-01 Speed

PID Droop

. This ensures that the motors share the load evenly. A side effect of using speed PID droop is that the actual shaft speed

does not match the reference exactly. Speed PID droop is not efficient in low-speed applications because the adjustment range may
be insufficient.
Use speed trim if the application requires the following features:

Accurate speed (the actual shaft speed matches the reference speed).
Precise speed adjustment down to 0 RPM.

Enabling PID droop

To enable speed PID droop:

Run the drive in 1 of the following modes:

Flux closed loop (

parameter 1-01 Motor Control Principle

, 

[3] Flux w/ motor feedb

).

Flux sensorless (

parameter 1-01 Motor Control Principle

, 

[2] Flux sensorless

).

Run the drive in speed mode (

parameter 1-00 Configuration Mode

, option 

[0] Speed open loop

 or 

[1] Speed closed loop

).

Ensure that 

parameter 1-62 Slip Compensation

 contains the default value (0%).

Ensure that all drives in the torque sharing system use the same speed reference and start and stop signal.

AU275636650261en-000101 / 130R0334 | 253

Danfoss A/S © 2022.12

Parameter Descriptions

VLT AutomationDrive FC 301/302

Programming Guide

Содержание VLT AutomationDrive FC 301



















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов