Daikin GYEQ20AN, Руководство по обслуживанию

Страница: 94 / 245

Test Run Manual SiAUY361411EA
83 Device Overview
0FGHP-EN0841 DGJ002
– 16 –
2 How to Perform a Test Run
STOP Mode
z When switching the slide switch SW1 to STOP, the unit enters STOP mode.
z To leave the STOP mode, set SW1 to the RUN position so that the total operated hours are displayed.
Be careful. The outdoor unit starts operation if the remote controller is in the operation mode when
SW1 is shifted to RUN.
z STOP mode has five levels from 1 to 5. Use the BACK and NEXT buttons to shift between these
levels.
z The channels are shifted using UP
and DOWN buttons.
Level 1 Level 2 Level 3 Level 4 Level 5
CH
items
1. Alarm display Alarm display Alarm reset
2. Actuator check Actuator check Actuator check action
3. Configure items 01. ON/OFF unit (memory switch) Each item ON/OFF display Item data update
02. Not used
4. Alarm/warning history Alarms/warnings Among alarm/warning history
Alternate display of alarm content
* During STOP mode, the display is automatically returned to STOP 20 seconds after the termination of operation.
1. Alarm display
Enter STOP mode, make sure that the display [1] (CH1: alarm display) is selected at level 1 and press
NEXT to display the alarm code.
To clear the alarm conditions, hold down ENTER for 3 seconds.
2. Actuator check
Enter STOP mode, select CH [2] at level 1 and press NEXT . (2) Select the CH (refer to the table below)
at level 2 and press NEXT . (3) Change the set value as ON/OFF using UP and DOWN , and then
press ENTER for setting. If ENTER is pressed again, the setting becomes inactive.
When you change the setting to "ON", the value of "ON" will be applied after a five second countdown.
You can only set one actuator at a time to ON.
Ƒ7DEOH/LVWRI$FWXDWRU&KHFNV
CH Item Content CH Item Content CH Item Content
01 Starter ON/OFF (ON for 10 seconds) 28 Water Motor Valve ON/OFF 56 Gas valve 1 & 2 simultaneous check ON/OFF
02 Not used Do not turn this item off. 29 Throttle valve ON(H)/OFF 57 Vacant
03 Gas valve 1 ON/OFF 30 Fuel control valve ON(H)/OFF 58~59 Vacant
04 Gas valve 2 ON/OFF 31 Vacant 60 Vacant
05 Clutch 1 ON/OFF 32 Vacant 61 Vacant
06 Clutch 2 ON/OFF 33 Vacant 62 SV7 ON/OFF
07
Compressor heaters
1/2/oil return heater
ON/OFF
34 Vacant 63 Vacant
35 SV31 ON/OFF 64 SV9 ON/OFF
08 Not used 36 SV32 ON/OFF 65 Vacant
09 Oil separator heater ON/OFF 37 Vacant 66 Vacant
10 Exhaust drain heater ON/OFF 38 Vacant 67 Accumulator heater ON/OFF
11 Block heater ON/OFF 39 Vacant 68 Not used
12 Four-way valve 1 ON/OFF 40 Vacant 69 SV12 ON/OFF
13 SV1 ON/OFF 41 SV37 ON/OFF 70 SV12 and EV6 synchronized ON/OFF
14 SV2 ON/OFF 42 Vacant 71 SV13 ON/OFF
15 SV3 ON/OFF 43 Vacant 72 SV3A ON/OFF
16 SV4 ON/OFF 44 Vacant 73 SV3B ON/OFF
17 Vacant 45 Vacant 74 SV3C ON/OFF
18 Fan 1 ON(H)/OFF 46 Vacant 75 SV3D ON/OFF
19 Fan 2 ON(H)/OFF 47 Vacant 76 SV3E ON/OFF
20 Fan 3 ON(H)/OFF 48 Vacant 77 SV3F ON/OFF
21 Cooling water pump ON(H)/OFF 49 Vacant 78 SV3G ON/OFF
22 EV1 ON(H)/OFF 50 Vacant 79 SV3H ON/OFF
23 EV2 ON(H)/OFF 51 Vacant 80 EV7 ON(H)/OFF
24 EV3 ON(H)/OFF 52 Vacant 81 EV3A ON(H)/OFF
25 EV4 ON(H)/OFF 53 Vacant 82 EV3B ON(H)/OFF
26 EV5 ON(H)/OFF 54 Cooling water cool-down mode ON/OFF
27 EV6 ON(H)/OFF 55 Outdoor unit evacuation mode ON/OFF
* When the fan rotates quickly in reverse due to strong wind, it may not operate even when turned on. In that case, block the wind to
prevent the fan from turning in reverse. In CH54 cooling water cool-down mode, the cooling water pump and all fans operate
simultaneously despite rotation in reverse.