Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 46

Страница: 46 / 150

2-28

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

DTP Messages

Error Message

DTP-4-TMRERR: An internal timer error occurred when trunking on

interface [chars].

Explanation

A timer used by the trunking protocol unexpectedly expired. [chars] is the trunked

interface.

Recommended Action

This problem is corrected internally and has no long-term ramifications.

However, if more problems with trunking occur, reload the switch by using the

reload

privileged

EXEC command.

Error Message

DTP-4-UNKN_ERR: An unknown operational error occurred.

Explanation

The system cannot negotiate trunks because an internal operation generated an

unexpected error.

Recommended Action

Reload the switch by using the

reload

privileged EXEC command.

Error Message

DTP-5-DOMAINMISMATCH: Unable to perform trunk negotiation on port

[chars] because of VTP domain mismatch.

Explanation

The two ports in the trunk negotiation belong to different VTP domains. Trunking can

be configured only when the ports belong to the same VTP domain. [chars] is the port number.

Recommended Action

Ensure that the ports in the trunk negotiation belong to the same VTP domain.

Error Message

DTP-5-ILGLCFG: Illegal config (on, isl--on,dot1q) on [chars].

Explanation

One end of the trunk link is configured as

with ISL encapsulation and that the other

end is configured as

with 802.1Q encapsulation. [chars] is the interface.

Recommended Action

This configuration is illegal and will not establish a trunk between two

switches. You must change the encapsulation type so that both ends of the trunk match.

Error Message

DTP-5-NONTRUNKPORTON: Port [chars] has become non-trunk.

Explanation

The interface changed from a trunk port to an access port. [chars] is the interface that

changed.

Recommended Action

This message is provided only for information.

Error Message

DTP-5-TRUNKPORTCHG: Port [chars] has changed from [chars] trunk to

[chars] trunk.

Explanation

The encapsulation type of the trunk port has changed. The first [chars] is the interface,

the second [chars] is the original encapsulation type, and the third [chars] is the new encapsulation
type.

Recommended Action

This message is provided only for information.

Содержание Catalyst 3560-E Series























































































































































Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды

Cisco Catalyst 3560-E Series, Руководство по эксплуатации

Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды