Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 83

Страница: 83 / 150

2-65

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

PLATFORM_PBR Messages

Error Message

PLATFORM_PBR-3-INSTALL_FAIL: Policy route-map [chars] not installed in

hardware.

Explanation

The PBR manager could not install the complete route-map in hardware, so the packets

are forwarded to the CPU for processing. [chars] is the route-map.

Recommended Action

Simplify route-map configurations. For example, use the same route-map on

multiple interfaces.

Error Message

PLATFORM_PBR-3-NO_LABEL: Cannot allocate label for route-map [chars].

Explanation

The PBR manager could not allocate a label for this route-map. As a result, the hardware

cannot be programmed to implement policy routing. There is a limit of 247 labels for policy routing.
[chars] is the route-map.

Recommended Action

Simplify the configuration with label sharing. Use the same route-maps on

multiple interfaces, if possible.

Error Message

PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map [chars] not supported for

Policy-Based Routing.

Explanation

The route-map attached to an interface for policy routing contains an action that is not

supported. This is a hardware limitation. [chars] is the route-map.

Recommended Action

Use the

route-map

map-tag

permit

global configuration command and the

set

ip next-hop

ip-address

route-map configuration command to reconfigure the route map to use only

these supported actions.

Error Message

PLATFORM_PBR-4-CPU_SUPPORTED_ACTION: Set action in sequence [dec] of

route-map [chars] supported by forwarding to CPU.

Explanation

The route-map attached to an interface for policy-based routing contains an action that

is not supported in hardware, so the packets are forwarded to the CPU for processing. The route-map
actions that invoke this forwarding are

set interface

set ip default next-hop

set default interface

set ip df

. [dec] is the action number, and [chars] is the route-map.

Recommended Action

Use the

set ip next-hop

ip-address

route-map configuration command to

reconfigure the route map action to route the packet to the specified next hop.

Error Message

PLATFORM_PBR-4-RETRY_INSTALL: Route-map [chars] installed in hardware

upon retry.

Explanation

The PBR manager was able to fit the complete configuration into the hardware. One or

more route-maps previously did not load because of lack of resources. [chars] is the route-map.

Recommended Action

No action is required.

Содержание Catalyst 3560-E Series























































































































































Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды

Cisco Catalyst 3560-E Series, Руководство по эксплуатации

Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды