Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 150

background image

2-98

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

SPAN Messages

Explanation

A stack member cannot support the SDM template that the stack master is using.

Switches in the SDM mismatch state are not functional stack members. This error follows the
STACKMGR-6-SWITCH_ADDED_SDM error message if it reports SDM_MISMATCH. [chars]
displays mismatch information and recommended corrective actions.

Recommended Action

Downgrade the SDM template of the stack master to make it compatible with

the stack member switches. For example, if the stack master uses the aggregator routing template,
the message recommends downgrading the stack master to the desktop routing template by using the

sdm prefer vlan desktop

global configuration command.

SPAN Messages

Error Message

SPAN-3-MEM_UNAVAIL: Memory was not available to perform the SPAN

operation.

Explanation

The system could not perform a SPAN operation because of a lack of memory.

Recommended Action

Reduce other system activity to ease the memory demands.

Error Message

SPAN-3-SESS_DEC_CFG: SPAN hardware resource is in use. [chars]

Explanation

The system could not allocate a SPAN hardware resource for the feature specified in the

error message. It is possible that a distributed EtherChannel has been configured in the system that
is using a SPAN hardware resource.

Recommended Action

Remove one or all of the distributed EtherChannels from the system and retry

the operation.

Error Message

SPAN-3-SESS_HW_UNAVAIL: SPAN hardware resource not available [chars]

Explanation

The system could not allocate a SPAN hardware resource for the feature specified in the

error message. A possible cause is that all SPAN source sessions are already in use. The system can
be configured with a maximum of two SPAN source sessions or one RSPAN source session. [chars]
is the unavailable resource.

Recommended Action

Remove one of the existing SPAN or RSPAN source sessions, and retry the

operation.

Error Message

SPAN-3-UNKN_ERR: An internal error occurred during a SPAN operation.

Explanation

SPAN detected an error in its internal operation.

Recommended Action

The error might be transient. Try the SPAN operation again. If a second attempt

also fails, reload the switch by using the

reload

privileged EXEC command to complete the

operation.

«
...
114
115
116
117
118
...
»

Содержание Catalyst 3560-E Series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3560-E Series

Бренд: ZALMAN Страницы: 20

Бренд: Datasat Страницы: 32

Module NI PXI-8250

Бренд: National Instruments Страницы: 39

Бренд: Furuno Страницы: 24

Proventia A1204

Бренд: Internet Security Systems Страницы: 42

VMG5313-BXB SERIES

Бренд: ZyXEL Communications Страницы: 2

Бренд: Arbor Technology Страницы: 8

Бренд: Patton electronics Страницы: 2

Бренд: Supermicro Страницы: 15

Бренд: LUX LUMEN Страницы: 41

Бренд: Black Box Страницы: 62

Бренд: Extreme Networks Страницы: 51

PC/104-PCMCIA-1

Бренд: Kontron Страницы: 20

Бренд: Renesas Страницы: 6

Analog Pulse Generator 812-OP/H

Бренд: Link electronics Страницы: 2

Бренд: Belkin Страницы: 2

Бренд: ADTRAN Страницы: 4

UEZGUI-4357-70WVN

Бренд: FDI Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды