Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 150

background image

2-44

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

IFMGR Messages

IFMGR Messages

Error Message

IFMGR-3-IFINDEX_PERSIST_ENTRY_CORRUPT: [chars] seems to be corrupted.

Trying to read [dec] size

Explanation

The ifIndex table is corrupted. [chars] is the path to the IfIndex file, and [dec] is the

number of bytes that was being read from the ifIndex table when the corruption was detected.

Recommended Action

Delete the ifIndex table.

Error Message

IFMGR-3-INVALID_PERSISTENT_DATA: Invalid persistent data

Explanation

The interface manager attempted to write invalid persistent data.

Recommended Action

Copy the message exactly as it appears on the console or in the system log.

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to
look for similar reported problems. If you still require assistance, open a case with the TAC, or
contact your Cisco technical support representative, and provide the representative with the gathered
information.

IGMP_QUERIER Messages

Error Message

IGMP_QUERIER-4-NO_IP_ADDR_CFG: The IGMP querier cannot send out

General Query messages in VLAN [dec] because there is no IP address configured on

the system.

Explanation

An IP address for the IGMP querier was not configured at either the global or per-VLAN

level. [dec] is the VLAN ID.

Recommended Action

Configure a source IP address for the IGMP querier.

Error Message

IGMP_QUERIER-4-PIM_ENABLED: The IGMP querier is operationally disabled

in VLAN [dec] because PIM has been enabled on the SVI.

Explanation

Protocol-Independent Multicast (PIM) was detected on the switch virtual interface

(SVI). Do not enable the IGMP querier when PIM is enabled on the SVI. [dec] is the VLAN ID.

Recommended Action

Ensure that PIM is disabled on the SVI.

Error Message

IGMP_QUERIER-4-SNOOPING_DISABLED: The IGMP querier is operationally

disabled in VLAN [dec] because IGMP snooping has been disabled in this VLAN.

Explanation

IGMP snooping is disabled on this VLAN. Do not enable the IGMP querier when IGMP

snooping is disabled. [dec] is the VLAN IDs.

Recommended Action

Confirm that IGMP snooping is enabled both globally and on the VLAN.

«
...
60
61
62
63
64
...
»

Содержание Catalyst 3560-E Series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3560-E Series

IES615-2D Series

Бренд: 3onedata Страницы: 3

Бренд: 3One data Страницы: 5

Бренд: 3onedata Страницы: 33

Бренд: ICP DAS USA Страницы: 48

Бренд: ICP DAS USA Страницы: 24

Бренд: ICP DAS USA Страницы: 4

Бренд: D-Link Страницы: 176

Asynchronous SH7145F

Бренд: Renesas Страницы: 17

Бренд: TRENDnet Страницы: 2

Бренд: Quectel Страницы: 23

Бренд: Bridgeworks Страницы: 18

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

Бренд: ZyXEL Communications Страницы: 125

Protege PRT-PX16-PCB

Бренд: ICT Страницы: 34

ADSL 2/2+ VPN Firewall Router ADE-4300A/B

Бренд: Planet Страницы: 132

HBJC924R3288DG2NS Series

Бренд: JETWAY Страницы: 6

Бренд: 1&1 Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды