Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 77

Страница: 77 / 150

2-59

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

PLATFORM_ENV Messages

Error Message

PLATFORM_ENV-1-RPS_SYS_POWER_GOOD: [chars].

Explanation

The RPS 2300 system power state changed to

good

. [chars] is the error message.

Recommended Action

No action is required.

Error Message

PLATFORM_ENV-1-RPS_THERMAL_CRITICAL: RPS temperature has reached

critical threshold.

Explanation

The temperature sensor value in the RPS 2300 has reached the critical threshold. It

cannot function normally.

Recommended Action

The external temperature is too high. Immediately reduce the room

temperature in the room.

Error Message

PLATFORM_ENV-1-TEMP: Abnormal temperature detected.

Explanation

An abnormal temperature is detected.

Recommended Action

Ensure that ambient temperature is not too high. If the message appears again,

check the switch temperature by entering the

show env all

privileged EXEC command.

Error Message

PLATFORM_ENV-2-RPS_THERMAL_WARNING: RPS temperature has reach warning

threshold.

Explanation

The temperature sensor value in the RPS 2300 has reached the warning threshold. The

RPS can function normally until the temperature reaches the critical threshold.

Recommended Action

The external temperature is high. Reduce the room temperature.

Error Message

PLATFORM_ENV-3-RPS_BACKOFF_FAILED: [chars].

Explanation

The RPS 2300 is continuing to back up the switch even though the command on the

switch instructs it to no longer provide power to the switch. [chars] is the error message.

Recommended Action

No action is required.

Error Message

PLATFORM_ENV-3-RPS_CHANGE_TO_STANDBY: [chars].

Explanation

The RPS 2300 state changed to

standby

. It can no longer provide power to the switch.

[chars] is the error message.

Recommended Action

No action is required.

Содержание Catalyst 3560-E Series























































































































































Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды

Cisco Catalyst 3560-E Series, Руководство по эксплуатации

Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды