Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 63

Страница: 63 / 150

2-45

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

ILET Messages

Error Message

IGMP_QUERIER-6-PIM_DISABLED: The IGMP querier is now operationally

enabled in VLAN [dec] because PIM is no longer enabled on the SVI.

Explanation

PIM is disabled on the SVI, and the IGMP querier function is now enabled. [dec] is the

VLAN ID.

Recommended Action

No action is required.

Error Message

IGMP_QUERIER-6-SNOOPING_ENABLED: The IGMP querier is now operationally

enabled in VLAN [dec] because IGMP snooping is no longer disabled.

Explanation

IGMP snooping was enabled. As a result, the IGMP querier function is now enabled.

[dec] is the VLAN ID.

Recommended Action

No action is required.

ILET Messages

Error Message

ILET-1-AUTHENTICATION_FAIL: This Switch may not have been manufactured

by Cisco or with Cisco’s authorization. This product may contain software that

was copied in violation of Cisco’s license terms. If your use of this product is

the cause of a support issue, Cisco may deny operation of the product, support

under your warranty or under a Cisco technical support program such as Smartnet.

Please contact Cisco’s Technical Assistance Center for more information.

Explanation

A license authentication failure occurred for the switch.

Recommended Action

Contact your Cisco sales representative for assistance.

Error Message

ILET-1-DEVICE_AUTHENTICATION_FAIL: The [chars] inserted in this switch

may not have been manufactured by Cisco or with Cisco's authorization. If your use

of this product is the cause of a support issue, Cisco may deny operation of the

product, support under your warranty or under a Cisco technical support program

such as Smartnet. Please contact Cisco's Technical Assistance Center for more

information.

Explanation

A license authentication failure occurred for a component that was installed in the

switch. [chars] is the component.

Recommended Action

Contact your Cisco sales representative for assistance.

Содержание Catalyst 3560-E Series























































































































































Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды

Cisco Catalyst 3560-E Series, Руководство по эксплуатации

Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды