Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 150

background image

2-91

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

POWERNET_ISSU Messages

Error Message

PORT_SECURITY-6-VLAN_FULL: Vlan [dec] on port [chars] has reached its

limit. Address [enet] has been removed.

Explanation

The voice VLAN is the same as the access VLAN. Because the maximum number of

MAC addresses allowed on the access VLAN has been reached, the specified Ethernet address has
been deleted. [dec] is the VLAN ID, [chars] is the port assigned to the voice VLAN and the access
VLAN, and [enet] is the Ethernet address.

Recommended Action

No action is required.

Error Message

PORT_SECURITY-6-VLAN_REMOVED: VLAN [int] is no longer allowed on port

[chars]. Its port security configuration has been removed.

Explanation

A configured VLAN is not allowed either due to a port mode change or an allowed

VLAN list change and is removed from the configuration. [int] is the VLAN ID, and [chars] is the
switch port assigned to the VLAN.

Recommended Action

No action is required.

POWERNET_ISSU Messages

Error Message

POWERNET_ISSU-4-SM_EW_DOMAIN_MISMATCH: Energywise domain of

EtherSwitch is [chars], recommended to have [chars].

Explanation

The EnergyWise domain of the service module does not match that of the switch. The

first [chars] is the EnergyWise domain of the service module. The second [chars] is the EnergyWise
domain of the router.

Recommended Action

Configure the EnergyWise domain of the service module to match that of the

switch. If the message recurs, copy the message exactly as it appears on the console or in the system
log. Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit
to look for similar reported problems. If you still require assistance, open a case with the TAC, or
contact your Cisco technical support representative, and provide the representative with the gathered
information.

Note

This message applies only to the Catalyst 3750-X and 3560-X switches.

«
...
107
108
109
110
111
...
»

Содержание Catalyst 3560-E Series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3560-E Series

Бренд: 3Com Страницы: 20

Бренд: Wave wifi Страницы: 2

Бренд: Palo Alto Network Страницы: 56

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 32

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: National Instruments Страницы: 9

Бренд: TRENDnet Страницы: 2

ACC-CX3RDK-CU5640

Бренд: e-con Systems Страницы: 9

NJ220 - IntelliJack Switch

Бренд: 3Com Страницы: 82

Conel UR5i v2 Libratum

Бренд: B&B Electronics Страницы: 32

Protege PRT-PX16-PCB

Бренд: ICT Страницы: 34

ADSL 2/2+ VPN Firewall Router ADE-4300A/B

Бренд: Planet Страницы: 132

Marconi OMS 1200

Бренд: Ericsson Страницы: 136

Бренд: Abocom Страницы: 2

Бренд: Zonet Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды