Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 150

background image

2-107

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

SPANTREE_VLAN_SW Messages

SPANTREE_VLAN_SW Messages

Error Message

SPANTREE_VLAN_SW-2-MAX_INSTANCE: Platform limit of [dec] STP instances

exceeded. No instance created for [chars] (port [chars]).

Explanation

The number of currently active VLAN spanning-tree instances has reached a

platform-specific limit. No additional VLAN instances are created until the existing number of
instances drops below the platform limit. [dec] is the spanning-tree instance limit, the first [chars]
is the smallest VLAN ID of those VLANs that cannot have spanning-tree instances created, and the
second [chars] is the port number.

Recommended Action

Reduce the number of currently active spanning-tree instances by either

disabling some of the currently active spanning-tree instances or deleting the VLANs associated
with them. You must manually enable the spanning trees that could not be created because of limited
instances.

STACKMGR Messages

Note

These messages apply only to Catalyst 3750-X and 3750-E switches.

Error Message

STACKMGR-3-HDM_GET_DEVICE_RECORD_FAIL: Device Manager could not get

device record.

Explanation

This switch could not get the device record for some or all other switches in the stack.

Recommended Action

Copy the message exactly as it appears on the console or in the system log.

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to
look for similar reported problems. If you still require assistance, open a case with the TAC, or
contact your Cisco technical support representative, and provide the representative with the gathered
information. For more information about these online tools and about contacting Cisco, see the

“Error

Message Traceback Reports” section on page 1-7

.

Error Message

STACKMGR-3-MSG_FAIL: Failed to retrieve stack message from port-asic

[dec] in direction [dec].

Explanation

The stack manager module did not retrieve stack messages. The first [dec] is the ASIC

ID, and the second [dec] is the direction.

Recommended Action

No action is required.

«
...
123
124
125
126
127
...
»

Содержание Catalyst 3560-E Series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3560-E Series

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 86

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

Бренд: Pantech Страницы: 17

Бренд: Qualys Страницы: 2

Parallel & Serial Port Checker PPC

Бренд: B&B Electronics Страницы: 4

Бренд: 3Com Страницы: 32

Optane Persistent Memory 200 Series

Бренд: Supermicro Страницы: 54

Бренд: Uniden Страницы: 5

Бренд: Idis Страницы: 20

UniFi LED ULED-AT

Бренд: Ubiquiti Страницы: 16

Бренд: ZyXEL Communications Страницы: 3

Бренд: Quatech Страницы: 5

Бренд: Honeywell Home Страницы: 36

Бренд: Omron Страницы: 11

Бренд: Altronix Страницы: 8

PowerForce G4 '47

Бренд: PowerLogix Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды