Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 34

Страница: 34 / 150

2-16

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

CLS_ACC Messages

Error Message

CLS_ACC-5-CLRCFG: User cleared switch configurations under recovery

mode

Explanation

The switch resets to the default configuration in recovery mode.

Recommended Action

No action is required.

Error Message

CLS_ACC-5-RSTIMG: User reset switch image to factory default image

under recovery mode

Explanation

In recovery mode, the switch image resets to the default image.

Recommended Action

No action is required.

Error Message

CLS_ACC-7-ACC_INTF: Selected management interface: [chars] interface

number: [dec]

Explanation

An interface has been selected for Express Setup. [chars] is the name of the interface,

and [dec] is the number of the interface.

Recommended Action

No action is required.

Error Message

CLS_ACC-7-ACC_VLAN: Selected vlan [dec] for consoleless access

Explanation

The switch assigned a VLAN to the management interface for consoleless access. [dec]

is the VLAN ID.

Recommended Action

No action is required.

Error Message

CLS_ACC-7-CONFIG: Save access intf config: if: [chars], port num:

[dec], vlan [dec], admin-down?:[dec]

Explanation

The switch has saved the interface configuration. After the switch exits Express Setup

mode and the management interface is configured, the saved configuration takes effect. [chars] is
the name of the mode. The first [dec] is the port number, the second [dec] is the VLAN ID, and the
third [dec] is the port status.

Recommended Action

No action is required.

Error Message

CLS_ACC-7-CONFIG_SUCCESS: [chars]

Explanation

The management interface has been configured, or its original configuration has been

restored. [chars] is the name of the configuration file.

Recommended Action

No action is required.

Содержание Catalyst 3560-E Series























































































































































Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды

Cisco Catalyst 3560-E Series, Руководство по эксплуатации

Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды