Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 150

background image

2-36

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

FRNTEND_CTRLR Messages

FRNTEND_CTRLR Messages

Note

These messages apply only to the Catalyst 3750-X and 3750-E switches.

Error Message

FRNTEND_CTRLR-1-MGR_TXQ_FULL: The front end controller Tx queue

reached watermark level

Explanation

There are too many messages in the queue between the front-end controller and the

switch software.

Recommended Action

Reset the switch. If the problem is not resolved, contact your Cisco technical

support representative because there might be a problem with the switch.

Error Message

FRNTEND_CTRLR-2-SUB_INACTIVE: The front end controller [dec] is

inactive.

Explanation

The front-end controller that controls the LEDs, the PoE features, and the fan-control

features is now inactive on the port controlled by the front-end controller. This does not affect the
traffic on the port. [dec] is the controller number.

Recommended Action

Reset the switch. If the problem is not resolved, contact your Cisco technical

support representative because there might be a problem with the switch.

GBIC_SECURITY Messages

Note

The Catalyst 3750-X, 3750-E, 3560-X, and 3560-E switches support SFP modules and do not support
GBIC modules. Although the error message text refers to GBIC interfaces and modules, the messages
from the switches actually refer to the SFP and 10-Gigabit Ethernet module interfaces and modules.

Error Message

GBIC_SECURITY-4-EEPROM_CRC_ERR: EEPROM checksum error for GBIC in

[chars].

Explanation

The GBIC in the specified port has invalid EEPROM data. [chars] is the port in which

the GBIC is inserted.

Recommended Action

Remove the GBIC from the port.

Error Message

GBIC_SECURITY-4-EEPROM_READ_ERR: Error in reading GBIC serial ID in

[chars].

Explanation

An error occurred while the switch was reading the GBIC type from the EEPROM.

[chars] is the port in which the GBIC is inserted.

Recommended Action

Remove the GBIC from the port.

«
...
52
53
54
55
56
...
»

Содержание Catalyst 3560-E Series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3560-E Series

Professional Series

Бренд: PACOM Страницы: 15

Бренд: Campbell Страницы: 42

Бренд: Eaton Страницы: 10

Бренд: Quick Eagle Networks Страницы: 4

Бренд: National Instruments Страницы: 26

Бренд: National Instruments Страницы: 85

Module SCXI-1503

Бренд: National Instruments Страницы: 79

Бренд: Google Страницы: 14

Бренд: Advantech Страницы: 36

Бренд: WABCO Страницы: 29

Бренд: EMTRUST Страницы: 103

Бренд: Network Critical Страницы: 200

UniFi WiFi BaseStation XG

Бренд: Ubiquiti Страницы: 19

Emotron OSTO 100

Бренд: CG Страницы: 112

Бренд: Idis Страницы: 16

Бренд: ZIMO Страницы: 13

Бренд: Comelit Страницы: 140

TigerSwitch 100 SMC6924VF

Бренд: SMC Networks Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды