Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 41

Страница: 41 / 150

2-23

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

DOT1X Messages

Error Message

DOT1X-5-ERR_TRUNK: Dot1x can not be enabled on Trunk port.

Explanation

802.1x authentication could not be enabled on the trunk port. An attempt to set 802.1x

port control to

auto

force-unauthorized

mode on a trunk port, which is not allowed, caused this

condition.

Recommended Action

Disable trunking on the interface, and re-enable 802.1x authentication on the

port.

Error Message

DOT1X-5-ERR_VLAN_INVALID: The VLAN [dec] is invalid and cannot be

assiged for use on the Dot1x port [chars] Vlan

Explanation

The specified VLAN is out of range and cannot be assiged as an 802.1x port. [dec] is

the VLAN, and [chars] is the 802.1x port.

Recommended Action

Reconfigure the configuration to use a valid VLAN.

Error Message

DOT1X-5-FAIL: Authentication failed for client ([chars]) on Interface

[chars] AuditSessionID [chars]

Explanation

The authentication was unsuccessful. The first [chars] is the client ID, the second

[chars] is the interface, and the third [chars] is the session ID.

Recommended Action

No action is required.

Error Message

DOT1X-5-INVALID_INPUT: Dot1x Interface parameter is Invalid on

interface [chars].

Explanation

The 802.1x interface parameter is out of the specified range or is invalid. [chars] is the

interface.

Recommended Action

See the command-line help string for the valid 802.1x parameters.

Error Message

DOT1X-5-INVALID_MAC: Invalid MAC address(drop, zero, broadcast or

multicast mac address) [enet] is trying to authenticate.

Explanation

Authentication using 802.1x is not allowed for zero, broadcast, and multicast source

MAC addresses. [enet] is the invalid MAC address.

Recommended Action

Connect an 802.1x supported host to the 802.1x enabled port.

Error Message

DOT1X-5-RESULT_OVERRIDE: Authentication result overridden for client

([chars]) on Interface [chars] AuditSessionID [chars]

Explanation

The authentication result was overridden. The first [chars] is the client ID, the second

[chars] is the interface, and the third [chars] is the session ID.

Recommended Action

No action is required.

Содержание Catalyst 3560-E Series























































































































































Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды

Cisco Catalyst 3560-E Series, Руководство по эксплуатации

Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды