Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 39

Страница: 39 / 150

2-21

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

DOT1X Messages

Error Message

DHCP_SNOOPING-6-VLAN_NOT_SUPPORTED: Vlan not supported. [dec] bindings

ignored.

Explanation

The specified number of bindings were ignored when the switch read the database file

because the VLAN is no longer configured on the switch. [dec] is the number of bindings that the
switch ignores.

Recommended Action

No action required.

DOT1X Messages

Error Message

DOT1X-4-MEM_UNAVAIL: Memory was not available to perform the 802.1X

action. AuditSessionID [chars]

Explanation

The system memory is not sufficient to perform the 802.1x authentication. [chars] is the

session ID.

Recommended Action

Reduce other system activity to reduce memory demands.

Error Message

DOT1X-4-PROC_START_ERR: Dot1x unable to start.

Explanation

The system did not start the 802.1x process.

Recommended Action

Restart the 802.1x process by entering the

dot1x system-auth-control

global

configuration command. If this message recurs, reload the device.

Error Message

DOT1X-4-UNKN_ERR: An unknown operational error occurred.

Explanation

The 802.1x process cannot operate because of an internal system error.

Recommended Action

Reload the device.

Error Message

DOT1X-5-ERR_CHANNELLING: Dot1x cannot be enabled on Channelling ports.

Explanation

802.1x authentication could not be enabled on the EtherChannel port. An attempt to set

802.1x port control to

auto

or to f

orce-unauthorized

mode on the channel port, which is not

allowed, caused this condition.

Recommended Action

Disable the EtherChannel on the interface, and then re-enable 802.1x

authentication.

Error Message

DOT1X-5-ERR_DYNAMIC: Dot1x cannot be enabled on Dynamic ports.

Explanation

802.1x authentication could not be enabled on the dynamic-mode port. An attempt to

set 802.1x port-control to

auto

force-unauthorized

mode on a dynamic mode port, which is not

allowed, caused this condition.

Recommended Action

Disable dynamic mode on the interface, and then try 802.1x authentication.

Содержание Catalyst 3560-E Series























































































































































Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды

Cisco Catalyst 3560-E Series, Руководство по эксплуатации

Результаты поиска

Содержание Catalyst 3560-E Series

Отзывы:

Похожие инструкции для Catalyst 3560-E Series

Бренды по названию

Популярные бренды