Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 150

background image

2-57

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

PLATFORM_ENV Messages

Error Message

PLATFORM_ENV-1-FRU_PS_SIGNAL_OK:[chars] signal on power supply is

restored.

Explanation

The specified signal of the power supply has been restored. [chars] is the signal value

(

12V

or

PoE

).

Recommended Action

No action is required.

Error Message

PLATFORM_ENV-1-PS_NONPOE: Internal Power supply not adequate for

inline power.

Explanation

The internal power supply does not provide enough power for the Power over Ethernet

(PoE) ports.

Recommended Action

Substitute a power supply that can provide enough power for the PoE ports.

Error Message

PLATFORM_ENV-1-RPS_ACCESS: [chars].

Explanation

An RPS 2300 communication error is detected. [chars] is the error message.

Recommended Action

Copy the message exactly as it appears on the console or in the system log.

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to
look for similar reported problems. If you still require assistance, open a case with the TAC, or
contact your Cisco technical support representative, and provide the representative with the gathered
information. For more information about these online tools and about contacting Cisco, see the

“Error

Message Traceback Reports” section on page 1-7

.

Error Message

PLATFORM_ENV-1-RPS_FAN_FAILED: [chars].

Explanation

An RPS 2300 fan failure is detected. [chars] is the error message.

Recommended Action

Disconnect any switches connected to the RPS 2300, and immediately replace

the fan.

Error Message

PLATFORM_ENV-1-RPS_OVER_CURRENT: [chars].

Explanation

An RPS 2300 over current condition is detected. [chars] is the error message.

Recommended Action

Disconnect the switches from the RPS 2300 that is not providing power to

them.

Error Message

PLATFORM_ENV-1-RPS_PS_FAN_FAILED: RPS power supply fan failure

detected [chars].

Explanation

An RPS 2300 power supply fan failure is detected. [chars] is the power supply ID (

A

or

B

).

Recommended Action

Disconnect any switches connected to the RPS 2300, and immediately replace

the power supply.

«
...
73
74
75
76
77
...
»

Содержание Catalyst 3560-E Series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3560-E Series

Бренд: GE Страницы: 146

Бренд: Cambium Networks Страницы: 68

Бренд: Cambium Networks Страницы: 110

DHI-NVR5224-24P-4KS2

Бренд: Dahua Страницы: 24

Бренд: PaloAlto Networks Страницы: 2

Бренд: Javad Страницы: 35

Armor 101 Series

Бренд: Lochinvar Страницы: 28

Armor 101 Series

Бренд: Lochinvar Страницы: 44

BladeCenter Management Module

Бренд: IBM Страницы: 184

Бренд: U.S. Products Страницы: 80

3C8567 - SuperStack II NETBuilder SI 567...

Бренд: 3Com Страницы: 6

Бренд: ZyXEL Communications Страницы: 79

Бренд: Zhone Страницы: 2

Бренд: National Instruments Страницы: 26

Total Access 1500 Dual FXS/DPO

Бренд: ADTRAN Страницы: 2

SecPath F50X0 Series

Бренд: H3C Страницы: 41

Бренд: NEC Страницы: 26

Бренд: TP-Link Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды