Cisco Catalyst 3560-E Series Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 150

background image

2-90

Catalyst 3750-X, 3750-E, 3560-X, and 3560-E Switch System Message Guide

OL-9772-05

Chapter 2 Message and Recovery Procedures

PORT_SECURITY Messages

contact your Cisco technical support representative, and provide the representative with the gathered
information. For more information about these online tools and about contacting Cisco, see

Error

Message Traceback Reports, page 1-7

.

PORT_SECURITY Messages

Error Message

PORT_SECURITY-2-PSECURE_VIOLATION:Security violation occurred caused

by MAC [enet] on port [chars].

Explanation

An unauthorized device attempted to connect on a secure port. [enet] is the MAC

address of the unauthorized device, and [chars] is the secure port.

Recommended Action

Identify the device that attempted to connect on the secure port. Notify your

network system administrator of this condition.

Error Message

PORT_SECURITY-2-PSECURE_VIOLATION_VLAN: Security violation on port

[chars] due to MAC address [enet] on VLAN [dec]

Explanation

An unauthorized device attempted to connect on a secure trunk port. [chars] is the

secure port, [enet] is the MAC address of the unauthorized device, and [dec] is the VLAN ID.

Recommended Action

Identify the device that attempted to connect through the secure trunk port.

Notify your network system administrator of this condition.

Error Message

PORT_SECURITY-6-ADDR_REMOVED: Address [dec]:[enet] exists on port

[chars]. It has been removed from port [chars].

Explanation

A routed port is reconfigured as a switch port. The address in the previous switch

configuration conflicts with the running configuration and has been deleted. [dec]:[enet] is the MAC
address of the port, and [chars] is the reconfigured port.

Recommended Action

No action is required.

Error Message

PORT_SECURITY-6-ADDRESSES_REMOVED: Maximum system secure address count

reached. Some secure addresses configured on port [chars] removed.

Explanation

Some configured and sticky MAC addresses on the specified port were removed from

the configuration. The number of secure addresses that the system supports was exceeded. This
condition occurs only during hot swapping or port-mode changes (for example, when the port is
converted from a Layer 3 to a Layer 2 port). [chars] is the port.

Recommended Action

No action is required.

«
...
106
107
108
109
110
...
»

Содержание Catalyst 3560-E Series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3560-E Series

Бренд: Hal Communications Страницы: 25

Бренд: Zonet Страницы: 8

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Бренд: D-Link Страницы: 53

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

LightSpeed Appliance QLS250

Бренд: Quantum Страницы: 12

Бренд: mikroElektronika Страницы: 3

X-Pedition 2000

Бренд: Enterasys Страницы: 86

Бренд: ZyXEL Communications Страницы: 2

Бренд: Omega Engineering Страницы: 34

ION 1200 Series

Бренд: PaloAlto Networks Страницы: 90

Бренд: Garderos Страницы: 23

Marconi OMS 1200

Бренд: Ericsson Страницы: 136

Бренд: Radicom Страницы: 27

RCO-3000 Series

Бренд: C&T Solution Страницы: 96

Бренд: TRENDnet Страницы: 62

Optane Persistent Memory 200 Series

Бренд: Supermicro Страницы: 54

Бренд: Billion Страницы: 120

Бренд: Freescale Semiconductor Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды